Aclara Power-Line Systems Inc. Y72572-1 사용자 설명서
U n i v e r s a l M e t e r i n g T r a n s p o n d e r f o r k V 2 c ™ M e t e r U s e r G u i d e
17
Chapter 2 • Functional Description
Meter Optical Port Support
N
OTE
All serial port opcodes defined for the UMT-C-KV are accessible through the
meter optical port.
Communications between the meter optical port and the UMT-C-KV
Test/Programming Serial Port begins with the transponder receiving a specified
hexadecimal Identification Packet (IP) from the meter optical port - EE 80 20 00
00 01 20 20 75. After receiving the IP from the meter optical port the UMT-C-KV
transmits an acknowledgement back to the meter optical port, verifies the
password, sends an acknowledgement to the meter, and asserts its Modem Busy
line. The transmission of the Identification Packet and Security Packet conforms
to the ANSI C12.18 communication protocol. After password acknowledgement,
all communication between the meter optical port and the transponder uses the
Gateway Serial Protocol, GATEWAY-SPEC, in ASCII at 9600 baud.
Communication between the meter optical port and the transponder continues to
follow the gateway protocol until 1.0 +/- 0.01 seconds have passed since the last
communication. After this period has passed, the Modem Busy line is de-asserted.
Test/Programming Serial Port begins with the transponder receiving a specified
hexadecimal Identification Packet (IP) from the meter optical port - EE 80 20 00
00 01 20 20 75. After receiving the IP from the meter optical port the UMT-C-KV
transmits an acknowledgement back to the meter optical port, verifies the
password, sends an acknowledgement to the meter, and asserts its Modem Busy
line. The transmission of the Identification Packet and Security Packet conforms
to the ANSI C12.18 communication protocol. After password acknowledgement,
all communication between the meter optical port and the transponder uses the
Gateway Serial Protocol, GATEWAY-SPEC, in ASCII at 9600 baud.
Communication between the meter optical port and the transponder continues to
follow the gateway protocol until 1.0 +/- 0.01 seconds have passed since the last
communication. After this period has passed, the Modem Busy line is de-asserted.
Password Access
A default password is supplied to the customer for optical port access to the
transponder. The transponder contains a “Bad Password Counter”. After counting
4 incorrect passwords, the transponder locks out Serial Communication between
the meter optical port and the transponder Test/Programming Serial Port for 15
minutes. At the same time, the transponder sets bit 0 of register #36,”Indicators
Tamper”. Bit 0 of register #36 remains set until cleared by TNS. The “Bad
Password Counter” is cleared if no incorrect password has been received by the
transponder within the last 15 minutes.
transponder. The transponder contains a “Bad Password Counter”. After counting
4 incorrect passwords, the transponder locks out Serial Communication between
the meter optical port and the transponder Test/Programming Serial Port for 15
minutes. At the same time, the transponder sets bit 0 of register #36,”Indicators
Tamper”. Bit 0 of register #36 remains set until cleared by TNS. The “Bad
Password Counter” is cleared if no incorrect password has been received by the
transponder within the last 15 minutes.
Data Retrieval
The UMT-C-KV reads a subset of 32 registers as selected by the utility company.
All selected data are read at power-up and every five minutes thereafter if a valid
RCE Time Synchronization command was received. See Time Synchronization on
page 9.
All selected data are read at power-up and every five minutes thereafter if a valid
RCE Time Synchronization command was received. See Time Synchronization on
page 9.
N
OTE
Some features and capabilities of the transponder may not be supported, or may
be only partially supported by some versions of master station software.
Consumption Metering (Wh)
The UMT-C-KV provides remote access to the energy measurement registers of
the kV2c meter. The UMT-C-KV retrieves appropriate values from the meter’s
internal ANSI Standard tables. The UMT-C-KV retrieves data from only
“programmed” kV2c registers. When requested, the UMT-C-KV can supply data
from the latest read.
the kV2c meter. The UMT-C-KV retrieves appropriate values from the meter’s
internal ANSI Standard tables. The UMT-C-KV retrieves data from only
“programmed” kV2c registers. When requested, the UMT-C-KV can supply data
from the latest read.