dormakaba Canada Inc. R79KSR 사용자 설명서
Controller
Board
Board
124-511689-002
1 2 3
Bypass
Active
Reset
SW1
SW2
D46
D45
D41
D42
J1
J2
J3
J5
J6
J7
J8
J9
J12
J13
J14
J15
J16
J17
J18
J19
D43
D44
Programming
Port
SW3
WHIT
E
GREEN
WHIT
E
GREEN
BLACK
RE
D
BLACK
ON
1 2 3 1 2 3
1
2
3
1
2
3
1
2
3
1
2
1
2
3
4
1
23
4
12
3
4
12
3
4
1 2 3 1 2 3 4
1 2 3 4
For EGRESS
Application
Application
RE
D
For INGRESS
Application
Application
See Note 1*
WHIT
E
GREEN
BLAC
K
J4
2 1
J5
2 1
RE
D
Controller Board to RFID Wall Mounted Reader Connection
RAC4/4XT Controller Board Connection
Signal
Reader Connection
GND
J4 - 2
J1, Pin 2
J14, Pin 2
+12V
J4 - 1
J1, Pin 3
J14, Pin 3
RS485+
J5 - 2
J2, Pin 1 + J3, Pin 1*
J13, Pin 1 + J12, Pin 1
RS485-
J5 - 1
J2, Pin 2 + J3, Pin 2*
J13, Pin 2 + J12, Pin 2
Green
See Note 1
Note 1: Jumper cables as shown in figure B must be connected for the reader to operate correctly.
Wire Color
Red
Black
See Note 1
White
Comments
GND
+12V
Ingress Reader
Terminal Block
Egress Reader
Kaba Ilco Inc.
7301 Boul. Décarie, Montréal, Québec, H4P 2G7
T: (514) 735-5411, TF: 1-800-906-4526, F: (514) 735-1394
lodgingtech@kaba.com, www.kabalodging.com
7301 Boul. Décarie, Montréal, Québec, H4P 2G7
T: (514) 735-5411, TF: 1-800-906-4526, F: (514) 735-1394
lodgingtech@kaba.com, www.kabalodging.com
PK3660_10_14 Printed in Canada
Figure A: RFID Wall Mounted Reader
Surface Mount
Flush Mount
Table 1: RAC 4/4XT RFID Wall Mounted Reader Wire Connections
Figure B: RAC 4XT Controller Board
(Note: RAC 4 Ingress only)
Installation Sheet
RFID Wall Mounted Reader
Installed with ILCO RAC 4 or RAC 4XT
Installed with ILCO RAC 4 or RAC 4XT
Regulatory Compliance:
This device complies with Part 15 of the FCC Rules,. Operation is subject to the following two conditions: (1) this device may not cause harmful inter-
This device complies with Part 15 of the FCC Rules,. Operation is subject to the following two conditions: (1) this device may not cause harmful inter-
ference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.
“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.
“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”
FCC # Q8SR79KSR
FCC # Q8SR79KSR
IC# 4652A-R79KSR