Graco Children's Products Inc PD160487 사용자 설명서
Parent Unit
• The battery must be plugged into the Parent Unit before the
unit will be ready for use. Remove the battery door cover on the
Parent Unit with a key or flat blade screw driver. Remove the battery
pack from the packaging and plug into the back of the unit. Place
the battery pack into the recess and press the wire into the slot on
the side. Replace the battery door.
Nursery Unit
• Turn the unit over, and use screw driver to remove the battery door.
• Place 3-AAA (1.5V-LR03) batteries into the battery compartment. Note
• The battery must be plugged into the Parent Unit before the
unit will be ready for use. Remove the battery door cover on the
Parent Unit with a key or flat blade screw driver. Remove the battery
pack from the packaging and plug into the back of the unit. Place
the battery pack into the recess and press the wire into the slot on
the side. Replace the battery door.
Nursery Unit
• Turn the unit over, and use screw driver to remove the battery door.
• Place 3-AAA (1.5V-LR03) batteries into the battery compartment. Note
the proper orientation of the batteries.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon zinc), or rechargeable
• Do not mix alkaline, standard (carbon zinc), or rechargeable
(ni-cadmium, etc) batteries.
• Place the battery door back on the unit.
• Please remove a dead battery promptly. A dead battery left in the unit
• Please remove a dead battery promptly. A dead battery left in the unit
may leak, damaging your unit.
• Do not attempt to recharge a non-rechargeable battery.
• A rechargeable battery CANNOT be recharged by plugging the AC
• A rechargeable battery CANNOT be recharged by plugging the AC
adapter into the Nursery Unit.
• Remove the batteries from the unit if it is no longer being used or will
be stored for an extended period of time.
• The Parent Unit(s) can use either the rechargeable battery that comes with the unit or standard 120 volt AC household
current. The Nursery Unit uses 3-AAA (1.5V-LR03) batteries or standard 120 volt AC household current.
• To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit and the back of the
Nursery Unit, then plug adapter into a standard wall outlet.
• Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any
circumstances.
• If units do not work, check that AC adapters are plugged into working outlets.
• When electricity is off (from a power failure, etc.), the Nursery Unit will operate on 3-AAA (1.5V-LR03) batteries. If the Power
• When electricity is off (from a power failure, etc.), the Nursery Unit will operate on 3-AAA (1.5V-LR03) batteries. If the Power
LED is not lit, turn the power off and then back on to the Nursery Unit. A green LED indicates that the batteries are fine. A red
LED indicates that the batteries are low. If the LED does not light at all, then replace the batteries. The Parent Unit will operate
if the rechargeable battery is charged.
LED indicates that the batteries are low. If the LED does not light at all, then replace the batteries. The Parent Unit will operate
if the rechargeable battery is charged.
• In case you are experiencing some interference, the channel on the Nursery Unit can be changed by pressing the “ch”
button on the side of the unit. The Parent Unit will automatically scan all of the available channels until it locks on to the
Nursery Unit. If you are still experiencing interference, press the channel button on the side of the Nursery Unit up to 6
times until a good channel is found.
Nursery Unit. If you are still experiencing interference, press the channel button on the side of the Nursery Unit up to 6
times until a good channel is found.
Battery Installation
Using AC Adapters
Selecting Channels
3
+
-
+
-
+
-
Plug in cord
Batteries should be disposed of properly
by recycling.