Kenwo Industries Limited ARI60 사용자 설명서
Note:
If the optional factory connector kit is being used, please disregard this section of the
instructions and refer to the instructions supplied with the factory connector kit.
Note: All Connectors are unique and will only fit the appropriate component one way.
Mounting the Components
Select a suitable location under the seat or in a side cover. Mount the MCM using
Velcro or cable ties. Make sure that it is not exposed or easily reached.
Velcro or cable ties. Make sure that it is not exposed or easily reached.
Routing the Antenna Wire
The MCM includes an 18” antenna wire. The first 12” is a coaxial wire; the remaining 6” is
the reception antenna wire. When routing, try to avoid running the antenna along or
near metal. For best performance, have the antenna wire as vertical as possible and
exposed.
Wire Connections
The MCM is equipped with two connectors. One is for the main harness (HAR-1) and the
other is for the optional accessories.
other is for the optional accessories.
Accessory Harness
Plug in the accessory harness to the matching connector on the MCM. If no options are
being used, plug in the supplied dust cover.
Main Harness
The main harness consists of two harnesses. One is labeled (HAR-1) and the second is
labeled (GEN-1). Plug in the white 4 pin connector from the (HAR-1) into the matching 4
labeled (GEN-1). Plug in the white 4 pin connector from the (HAR-1) into the matching 4
pin connector from the (GEN-1). The (HAR-1) also has a waterproof connector that
plugs into the MCM. The wires should be connected as follows:
plugs into the MCM. The wires should be connected as follows:
HAR-1
Black wire with fuse and ring terminal – To battery Positive (+).
GEN-1
Black wire – To ground (-).
Grey wire – To turn signal power wire (Left).
Grey wire – To turn signal power wire (Left).
Grey wire – To turn signal power wire (Right).
Orange wire – To tail light wire or any other wire that is hot (+) when ignition is “ON”
(NOTE: this is an input to the alarm this connection is not designed to flash the tail light).
Orange wire – To tail light wire or any other wire that is hot (+) when ignition is “ON”
(NOTE: this is an input to the alarm this connection is not designed to flash the tail light).
Color Codes:
Ground (-)
Tail Light
Left Turn Signal Right Turn Signal
Honda
Green wire
Brown wire
Orange wire
Blue wire
Kawasaki
Black wire
Red wire
Green wire
Grey wire
Suzuki
Black/White Brown wire
Green or Black Grey wire
Yamaha
Black wire
Blue wire
Green wire
Brown wire
Harley Davidson
Black wire
Blue wire
Brown wire
Purple wire
3
Optional Accessories
Perimeter Sensor (SN-5)
Mounting the SN-5
The Perimeter sensor uses high frequency microwave technology to detect mass density
movement around the motorcycle. The signal can transmit through the seat, fiberglass,
The Perimeter sensor uses high frequency microwave technology to detect mass density
movement around the motorcycle. The signal can transmit through the seat, fiberglass,
leather and plastic, but not metal. It is recommended to place this sensor under the
seat as close as possible to the center of the motorcycle. With the provided Velcro, you
seat as close as possible to the center of the motorcycle. With the provided Velcro, you
can mount this sensor on top of the battery or any flat surface, making sure that the top
side of the sensor is facing upwards. Place Perimeter sensor as far away as possible fro
side of the sensor is facing upwards. Place Perimeter sensor as far away as possible fro
mthe MCM
Adjusting the Sensor
Although the sensor is pre set from the factory it may be necessary to adjust the
Although the sensor is pre set from the factory it may be necessary to adjust the
sensitivity to suit your specific application.
1. Stand at least 10’ away from the motorcycle and arm the system.
2. Walk towards the motorcycle and try and lean over the top of it. Once the sensor
2. Walk towards the motorcycle and try and lean over the top of it. Once the sensor
detects movement the siren will begin to chirp slowly. If you back away from the
motorcycle the siren will stop chirping. If you continue to move closer to the
motorcycle the siren will start to chirp faster and faster and then go into a full alarm.
motorcycle the siren will stop chirping. If you continue to move closer to the
motorcycle the siren will start to chirp faster and faster and then go into a full alarm.
3. Sensitivity can be adjusted by removing the plastic cap and tuning the adjustment
screw. To increase sensitivity, turn adjustment screw clockwise. To decrease
sensitivity, turn the adjustment screw counter clockwise.
sensitivity, turn the adjustment screw counter clockwise.
4.
The Perimeter sensor has an internal tuning control, which has been set at the
factory. This tuning control should only be changed if the sensor can not be
properly set as described in #3 above, please call Aritronix’ technical support.
factory. This tuning control should only be changed if the sensor can not be
properly set as described in #3 above, please call Aritronix’ technical support.
12
Plastic Cap :
Remove to adjust
sensitivity
Remove to adjust
sensitivity
To Accessory Harness on
Main Control Module (MCM)
Main Control Module (MCM)
Note: Do not turn sensitivity above half way. Doing so may cause false alarms.