ADC Telecommunications Inc. F0684-112 사용자 설명서

C-9

CONFIDENTIAL

{RF01}

Software error occurred and recovered.

If this happens repeatedly, replace the RAU.

{RF02}

Software error occurred and recovered.

If this happens repeatedly, replace the RAU.

{RF03}

Software error occurred and recovered.

If this happens repeatedly, replace the RAU.

{RF04}

Software reset occurred and recovered, 
or firmware download.

If this happens repeatedly, replace the RAU.

{RF05}

Software error occurred and recovered.

If this happens repeatedly, replace the RAU.

{RF06}

Problem detected in the RAU.

Contact TE Support for more information.

{RF07}

RAU power cycle.

RAU power cycle.

{RF08}

Problem detected in the RAU.

Contact TE Support for more information.

{RF09}

Invalid band.

The RAU doesn't support programmed band. Check the 
RAU type against the band programmed in the hub.

{RF10}

Low input DC voltage.

Check the coaxial cable for high RF loss. Try another 
Hub port. If the fault persists, replace the RAU. If the 
fault clears, mark the Hub port as unusable and replace 
the Hub when possible.

{RF11}

Hardware Failure (DL PLL Band 1).

Cycle power once. If the fault persists, replace the RAU.

{RF12}

Hardware Failure (DL PLL Band 2).

Cycle power once. If the fault persists, replace the RAU.

{RF13}

Hardware Failure (DL PLL Band 3).

Cycle power once. If the fault persists, replace the RAU.

{RF14}

Hardware Failure (UL PLL Band 1).

Cycle power once. If the fault persists, replace the RAU.

{RF15}

Hardware Failure (UL PLL Band 2).

Cycle power once. If the fault persists, replace the RAU.

{RF16}

Hardware Failure (UL PLL Band 3).

Cycle power once. If the fault persists, replace the RAU.

{RF17}

Hardware Failure (PA Band 1).

Cycle power once. If the fault persists, replace the RAU.

{RF18}

Hardware Failure (PA Band 2).

Cycle power once. If the fault persists, replace the RAU.

{RF19}

Hardware Failure (PA Band 3).

Cycle power once. If the fault persists, replace the RAU.

{RF20}

Hardware Failure (UL Pilot).

Cycle power once. If the fault persists, replace the RAU.

{RL21}

Commanded Out-of-service (Band 1).

Band 1 commanded out-of-service by User. Command 
In-Service on Band 1 to restore service.

{RL22}

Commanded Out-of-service (Band 2).

Band 2 commanded out-of-service by User. Command 
In-Service on Band 2 to restore service.

{RL23}

Commanded Out-of-service (Band 3).

Band 3 commanded out-of-service by User. Command 
In-Service on Band 3 to restore service.

{RF24}

Problem detected in the RAU.

Contact TE Support for more information.

{RX25}

Commanded shutdown (Band 1).

Check the status of hub to which the RAU is connected.

{RX26}

Commanded shutdown (Band 2).

Check the status of hub to which the RAU is connected.

{RX27}

Commanded shutdown (Band 3).

Check the status of the hub to which the RAU is con-
nected.

{RF28}

Internal shutdown (Band 1).

RAU Fault condition in band 1 path (or common path).

{RF29}

Internal shutdown (Band 2).

RAU Fault condition in band 2 path (or common path).

{RF30}

Internal shutdown (Band 3).

RAU Fault condition in band 3 path (or common path).

{RF31}

Hardware Failure (UL PLL2 Band 1).

Cycle power once. If the fault persists, replace the RAU.

{RF32}

Problem detected in the RAU.

Contact TE Support for more information.