Inovonics Wireless Corporation 3B6PORUNV 사용자 설명서
WMG200 Door/Window Transmitter
Installation and Instructions
CASE
HOLDING
POSTS(2)
HOLDING
POSTS(2)
PLATE
MOUNTING
HOLES(2)
MOUNTING
HOLES(2)
CONCEALED
WIRING
ENTRY
HOLE
WIRING
ENTRY
HOLE
CASE
LOCKING
TAB
LOCKING
TAB
MAGNET ALIGNMENT STRIP
BATTERY
RED
SWITCH
(INPUT 2)
SWITCH
(INPUT 2)
UNUSE
USE
ANTENNA
COVER
TAMPER
SWITCH
JUMPER
COVER HOLDING
HOOKS (2)
LOCKING TAB
RELEASE WINDOW
HOLE "A" (1)
BREAKOUT FOR SURFACE WIRING ACCESS
SLOT FOR CONCEALED
WIRING ACCESS
LOOP
TERMINALS
(INPUT1)
NOTE:
MG100
HAS 2
UNIQUE
ZONES
MAGNET
(OBTAIN
SEPARATELY)
1/2'' MAX
COVER PRY-OFF POINT
A
Diagram 1. Mounting Plate Diagram 2. Transmitter, Cover Removed
GENERAL INFORMATION
The WMG200 Door/Window Transmitter has its own unique serial number permanently assigned during manufacture. The
main control unit is required to “enroll” the transmitter serial No. at some point prior to its usage in the alarm system. Refer
to the main control unit’s installation instructions for further details.
The WMG200 has two unique zones: the first is for a wired closed circuit contact loop and the second for its built-in reed
switch (used in conjunction with a magnet as described below). Either or both zones may be used,
main control unit is required to “enroll” the transmitter serial No. at some point prior to its usage in the alarm system. Refer
to the main control unit’s installation instructions for further details.
The WMG200 has two unique zones: the first is for a wired closed circuit contact loop and the second for its built-in reed
switch (used in conjunction with a magnet as described below). Either or both zones may be used,
If you only use the
terminal input, don’t use built-in reed switch you must move jumper cap to unuse from use. The information to be sent are
Same for both zones
A built-in cover tamper switch is activated when the cover is removed.
Note: During programming of the main control unit, the WMG200 transmitters should be treated as Wireless Zone Type.
Same for both zones
A built-in cover tamper switch is activated when the cover is removed.
Note: During programming of the main control unit, the WMG200 transmitters should be treated as Wireless Zone Type.
INSTALLATION
Mounting
For proper orientation of the unit in relation to the mounting plate, loop wiring, and/or magnet, read all of this section
before installing the unit.
The description that follows assumes that the unit will be mounted as shown in the diagrams, with the magnet (if used)
located to the unit’s right. The unit may, however, be installed in any direction, as long as the relationship of the unit to its
mounting plate and magnet (if used) is maintained.
1. Remove the transmitter’s cover by inserting the flat blade of a small screwdriver in to the pry-off slot at the end of
For proper orientation of the unit in relation to the mounting plate, loop wiring, and/or magnet, read all of this section
before installing the unit.
The description that follows assumes that the unit will be mounted as shown in the diagrams, with the magnet (if used)
located to the unit’s right. The unit may, however, be installed in any direction, as long as the relationship of the unit to its
mounting plate and magnet (if used) is maintained.
1. Remove the transmitter’s cover by inserting the flat blade of a small screwdriver in to the pry-off slot at the end of
the unit farthest from the cover’s decorative ribs, and twisting the blade.
2. Disengage the supplied mounting plate from the unit by inserting the blade of a small screwdriver into the locking