Nortek Security & Control LLC/GTO Access SGER 사용자 설명서

The pushbutton labeled LEARN 2 is used to program transmitters to channel two. Momentarily press the receiver’s program button. The 

red programming LED will light. The LED slowly blinks 
for about 60 seconds. A transmitter must be entered 
while the LED is on. Press the desired learn button. The 
LED will flicker indicating that the receiver has accepted 
the transmitter and channel relay will toggle.

NOTE: Be sure to press the receiver program button 
for less than 2 seconds.

Be sure gate area is clear. Test the units by activating the gate and touching the 
edge sensor to ensure the gate obstructs.

Transmitters may be erased from the receiver’s memory by pressing and holding 
the receiver’s program button until the LED blinks one time as the receiver’s 
memory is erased. Then release the program button.

This Linear PRO Access (LPA) product is warranted against defects in material 
and workmanship for twelve (12) months. The Warranty Expiration Date is labeled 
on the product. This warranty extends only to wholesale customers who buy direct 
from LPA or through LPA’s normal distribution channels. LPA does not warrant 
this product to consumers. Consumers should inquire from their selling dealer as 
to the nature of the dealer’s warranty, if any. There are no obligations or liabilities 
on the part of LPA for consequential damages arising out of or in connection with 
use or performance of this product or other indirect damages with respect to loss 
of property, revenue, or profit, or cost of removal, installation, or re-installation. 
All implied warranties, including implied warranties for merchantability and implied 
warranties for fitness, are valid only until Warranty Expiration Date as labeled on 
the product. This LPA Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization 
Number (RPA#). Contact LPA Technical Services at 1-800-543-1236 for an 
RPA# and other important details

Linear PRO Access radio controls provide a reliable communications link and fill an 
important need in portable wireless signaling. However, there are some limitations 
which must be observed.

PRINTERS INSTRUCTIONS 
 INSTR,INSTL,SGER SERIES - GTO P/N: 

10016916

 - INK:  BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” -  SCALE: 1-1 - SIDE 2 of 2

CHANNEL TWO

PUSHBUTTON 

USE THIS

PUSHBUTTON

TO ENTER A

TRANSMITTER

INTO CHANNEL

TWO

LEARN 2

PRESS THE TRANSITTER

BUTTON ON THE CONTROL

BOARD

PRESS THE LEARN 

BUTTON FOR THE 

DESIRED CHANNEL

(LEARN 1 or LEARN 2)

THE LED WILL 

LIGHT AND REMAIN 

ON ABOUT FIVE 

SECONDS

RECEIVER LED WILL FLICKER

AS TRANSMITTER IS ENTERED

INTO MEMORY 

LED WILL FLASH, COUNTING 

THE TOTAL NUMBER OF 

TRANSMITTERS PROGRAMMED. 

THEN IT WILL BLINK ONCE 

(CHANNEL ONE) OR TWICE 

(CHANNEL TWO) AS THE 

TRANSMITTERS ARE ERASED.

PRESS PROGRAM BUTTON FOR 

FIVE SECONDS OR MORE

 

TOUCH THE EDGE 

SENSOR TO ENSURE 

THE GATE OBSTRUCTS

Copyright© 2017 GTO Access Systems, LLC

Document Number:  10016916 REV A (05-15-17)

SGER 

Alarm  Fault?   Condition

 Code
Low Batt  1 

NO 

Low Battery 

Open 

2 

YES 

No resistance across TB1 and TB2 of SGET

No Ack 

3 

YES 

SGET not able to send message 

 

 

 

(dead or too far away)

Edge 

4 

YES 

Edge shorted

NOTE: For AC Operator install an AC 
Sensor, and refer to the AC Sense 
instructions book. 

WARNING: Changes, modifications or adjustments not expressly approved by GTO 

Access Systems, LLC could void the user’s authority to operate this equipment. 
There Are No User Serviceable Parts.
NOTICE: This device complies with part 15 of the FCC rules and with Industry 

Canada license-exempt RSS standard(s). Operation is subject to the following two 
conditions: (1) this device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired operation 
of the device
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux 
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions 
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de 
l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d’en compromettre le fonctionnement.