ZyXEL Communications Corporation NWA1121NI 사용자 설명서
Chapter 6 Wireless LAN
NWA1121-NI User’s Guide
62
The following table describes the general wireless LAN labels in this screen.
Table 10
Wireless LAN > Wireless Settings: Root AP
LABEL
DESCRIPTION
Basic Settings
Wireless LAN
Interface
Interface
Select the check box to turn on the wireless LAN on the NWA1121-NI.
Operation Mode
Select Root AP from the drop-down list.
Wireless Mode
Select 802.11b/g to allow both IEEE802.11b and IEEE802.11g compliant WLAN devices
to associate with the NWA1121-NI. The transmission rate of your NWA1121-NI might be
reduced.
to associate with the NWA1121-NI. The transmission rate of your NWA1121-NI might be
reduced.
Select 802.11b/g/n to allow IEEE802.11b, IEEE802.11g and IEEE802.11n compliant
WLAN devices to associate with the NWA1121-NI. The transmission rate of the NWA1121-
NI might be reduced.
WLAN devices to associate with the NWA1121-NI. The transmission rate of the NWA1121-
NI might be reduced.
Select 802.11n to allow only IEEE802.11n compliant WLAN devices to associate with the
NWA1121-NI.
NWA1121-NI.
Channel
Select the operating frequency/channel depending on your particular region from the
drop-down list box.
drop-down list box.
Channel Width
This field displays only when you select 802.11n or 802.11b/g/n in the Wireless Mode
field.
field.
A standard 20MHz channel offers transfer speeds of up to 150Mbps whereas a 40MHz
channel uses two standard channels and offers speeds of up to 300Mbps. However, not all
devices support 40MHz channels.
channel uses two standard channels and offers speeds of up to 300Mbps. However, not all
devices support 40MHz channels.
Select the channel bandwidth you want to use for your wireless network.
It is recommended that you select 20/40MHz. This allows the NWA1121-NI to adjust the
channel bandwidth depending on network conditions.
channel bandwidth depending on network conditions.
Select 20MHz if you want to lessen radio interference with other wireless devices in your
neighborhood
neighborhood
or the wireless clients do not support channel bonding.
Select SSID
Profile
Profile
The SSID (Service Set IDentifier) identifies the Service Set with which a wireless station is
associated. Wireless stations associating to the access point (AP) must have the same
SSID.
associated. Wireless stations associating to the access point (AP) must have the same
SSID.
You can have up to four SSIDs active at the same time.
Note: If you are configuring the NWA1121-NI from a computer connected to the wireless
LAN and you change the NWA1121-NI’s SSID or security settings, you will lose your
wireless connection when you press Apply to confirm. You must then change the
wireless settings of your computer to match the NWA1121-NI’s new settings.
wireless connection when you press Apply to confirm. You must then change the
wireless settings of your computer to match the NWA1121-NI’s new settings.
#
This is the index number of each SSID profile.
Activve
Select the check box to enable an SSID profile. Otherwise, clear the check box.
Profile
Select an SSID Profile from the drop-down list box.
Universal Repeater Settings
The Universal repeater function allows the NWA1121-NI in root AP or repeater mode to set up a wireless
connection between it and another NWA1121-NI in root AP or repeater mode.
connection between it and another NWA1121-NI in root AP or repeater mode.
Note:
Universal repeater security
is independent of the security settings between the NWA1121-NI and any
wireless clients.
Local MAC
Address
Address
Local MAC Address is the MAC address of your NWA1121-NI.
Universal
Repeater SSID
Profile
Repeater SSID
Profile
Select the SSID profile you want to use for
universal repeater connections
.
Note: You can only configure None, WPA-PSK or WPA2-PSK security mode for the SSID
used by a universal repeater connection
.