Applied Concepts Inc ACMI007 사용자 설명서
Applied Concepts 011-0131-00 rev 2
Page 54
8.2 Software updates
The Dashboard program has the unique ability of uploading new software to Speed
Sensors with version 2.0.0 or later code already installed. If your Speed Sensor has
software that is earlier than 2.0.0, other PC Applications located on the Program CD can
be used for communicating to the Speed Sensor. Check with the factory to determine if
version 2.0.0 is available for your type of Speed Sensor. If software version 2.0.0 is
available, the Sensor can also be sent to the factory for upgrading to the latest program.
This section details the process of uploading a new software program to your Speed
Sensor
Sensors with version 2.0.0 or later code already installed. If your Speed Sensor has
software that is earlier than 2.0.0, other PC Applications located on the Program CD can
be used for communicating to the Speed Sensor. Check with the factory to determine if
version 2.0.0 is available for your type of Speed Sensor. If software version 2.0.0 is
available, the Sensor can also be sent to the factory for upgrading to the latest program.
This section details the process of uploading a new software program to your Speed
Sensor
8.3 Checking for a new version of software
Contact the Customer Service Department at Stalker Radar and inquire about a new
version of software. Please have your current version available when asked so it can be
determined if there is a new load for your Sensor. A new version can be sent by email
and will install on your hard drive under C:\Program Files\Stalker\.... in a sub folder that
groups the different versions together.
version of software. Please have your current version available when asked so it can be
determined if there is a new load for your Sensor. A new version can be sent by email
and will install on your hard drive under C:\Program Files\Stalker\.... in a sub folder that
groups the different versions together.
8.4 Dashboard Setup
Once the new code has been saved to your hard disk, open the Dashboard program.
Click on the “Options” menu and then click on “Reprogram Radar”. A new window will
appear as seen below. Follow the instructions to determine which type of Sensor you
have. Click on the appropriate selection box for your radar in the upper right corner of
the screen. Click on “OK” to proceed.
Click on the “Options” menu and then click on “Reprogram Radar”. A new window will
appear as seen below. Follow the instructions to determine which type of Sensor you
have. Click on the appropriate selection box for your radar in the upper right corner of
the screen. Click on “OK” to proceed.
Another window will open to show the available files that can be uploaded to the sensor.
Select the program that is to be uploaded to the unit, in this case “s3_sta_200.p” located
under the Stalker S3 Stationary section, see picture below. In this example, this
program is the latest version available for the Stationary type of Sensor. The folder
structure may vary by system. Double click on the icon of the desired version and click
on “Ok” on the popup window. The program will start to upload the code and a progress
meter will show at the bottom of the window. Programs for the RS485 versions of the
Speed Sensor will have the number “4” in the filename just before the revision number,
e.g. “s3_sta4_200.p”.
Select the program that is to be uploaded to the unit, in this case “s3_sta_200.p” located
under the Stalker S3 Stationary section, see picture below. In this example, this
program is the latest version available for the Stationary type of Sensor. The folder
structure may vary by system. Double click on the icon of the desired version and click
on “Ok” on the popup window. The program will start to upload the code and a progress
meter will show at the bottom of the window. Programs for the RS485 versions of the
Speed Sensor will have the number “4” in the filename just before the revision number,
e.g. “s3_sta4_200.p”.