VTech Telecommunications Ltd 80-0617-01 사용자 설명서

Pair and replace extra new baby

unit (VM)

You can add or replace any baby units (

VM3211

purchased separately) to your video and audio

monitor system. You can pair a maximum of

four baby units to your parent unit.

Press

MENU when the parent unit is idle.

Press or to choose , then press .
Press or to choose select a empty

camera

(

Press

SELECT

to confirm your selection.

Remove a paired baby unit (VM)

You can unpair baby unit from your video and

audio monitor system.

Press

MENU when the parent unit is idle.

Press or to choose , then press .
Press or to choose select the camera

you want to unpair

(

Press

SELECT.

Press

SELECT again to select

confirm your selection.

1.
2.
3.

4.
5.

Lullaby

You can play lullabies on the baby unit by

remoting on the parent unit. On the baby

unit, you can control the volume level of the

lullabies.

Playing lullabies

Press

MENU when the parent unit is idle.

Press or to choose , then press .
Press or to choose a lullaby, or choose

to stop playing.

Press

SELECT to confirm your selection.

Volume level control on baby unit

Press

VOL+ to increase the volume level of

the lullaby on the baby unit.
Press

VOL- to decrease the volume level of

the lullaby on the baby unit.

NOTES

Once the lullabies are played, the setting will be

applied to all registered baby units.
The lullaby playback on the baby unit will be

stopped when the broadcast from the parents unit

is playing. The lullabies will resume in several
seconds after the broadcast is ended.

1.
2.
3.

•

General product care

To keep this product working well and looking good,

follow these guidelines:

Avoid putting it near heating appliances and devices

that generate electrical noise (for example, motors or

fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft cloth.
DO NOT immerse the parent unit and the baby

unit in water and do not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the baby unit and parent unit are dry

before you connect them to the mains again.

Storage

When you are not going to use the baby monitor for

some time, remove the rechargeable battery from

the parent unit. Store the parent unit, the baby unit

and the adapters in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the baby monitor. If you cannot find the answer to your

question, visit our website at

www.vtechphones.com,

or contact

1 (800) 595-9511 for customer service.

Why does

the baby

monitor not

respond

normally?

Try the following (in the order

listed) for common cure:
1. Disconnect the power to the

baby units and the parent unit.

2. Remove the batteries in the

parent unit. Then install the

batteries again.

3. Wait a few seconds before

connecting power back to the

baby units and the parent unit.

4. Turn on the baby units and the

parent unit.

5. Wait for the parent unit to

synchronize with the baby units.

Allow up to one minute for this to

take place.

•

•
•
•
•

•
•

Why don’t

the power-on

light of the

baby unit and

parent unit

go on when I

switch on the

units?

Perhaps the parent unit is not

connected to the power. Insert

the appliance plug into the parent

unit and put the adapter in a wall

socket. Then press and hold to

switch on the parent unit and to

establish connection with the baby

unit.

Perhaps the baby unit is not

connected to the power. Connect

the baby unit to the mains. Then

set the

ON/OFF switch to ON

to switch on the baby unit and

to establish connection with the

parent unit.

Why doesn’t

my parent

unit charge

while

connected to

AC power?

Make sure the power is not

controlled by a wall switch.

Make sure the battery is installed.

You may have used the battery

for a long time. Replace a new

battery.

Why is my

screen in

black and

white?

The screen is in black and white

during night-time or in a dark room

when the night vision feature is

activated. This is normal due to

external light sources.

Why do I

get glare or

blurry display

on my screen

when viewing

my baby at

night?

During night-time or in a dark

room, the surroundings and other

interfering factors, like lightings,

objects, colors and backgrounds

may affect the image quality on

your parent unit screen. Adjust the

baby unit’s angle or place the baby

unit at a higher level to prevent

glare and blurry display.

Why does

the baby

monitor

produce a

high-pitched

noise?

The parent unit and baby units may

be too close to each other.

Move the parent unit away from

the baby units until the noise

stops; OR
Turn down the volume of your

parent unit.

•

Why does

the parent

unit beep?

The baby units may be out of

range. Move the parent unit closer

to the baby units (but not less than

3 feet).

If the parent unit is powered by the

provided battery, it may not have

enough charge for the parent unit to

perform normally. Charge the battery

in the parent unit for up to 3 hours.

The temperature of your baby’s

room may be too high or too low.

The

ON/OFF

light on the

baby unit

flashes and

the parent

unit displays

The baby unit is unpaired from the

parent unit. Follow below steps to

pair the baby unit. Make sure both

parent unit and baby unit are on

before pairing.

Press

MENU when the parent

unit is idle.
Press

to choose

then press .
Press or to choose an

empty baby unit slot ( , ,

or ), then press

SELECT.

The parent unit screen displays

Immediately press and hold

PAIR on the bottom of the

baby unit. The LED light

flashes quickly.

When pairing is successful, the

screen displays , followed the

view of the newly paired baby unit

SINGLE-CAM mode. The LED

light on the new baby unit remains

on.

If pairing fails, the screen

displays . Try the pairing

process again.
Only one baby unit can be

paired at a time.

•

Why don’t

I hear a

sound/Why

can’t I hear

my baby cry?

The parent unit speaker volume

may be too low or off. Press

VOL+

to increase the volume.

Why can’t I

establish a

connection?

Why is the

connection

lost every

now and

then? Why

are there

sound

interruptions?

The baby units may be out of

range. Move the parent unit closer

to the baby units (but not less than

3 feet).

Other electronic products may

cause interference with your baby

monitor. Try installing your baby

monitor as far away from these

electronic devices as possible.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to

reduce the risk of fire, electric shock and

injury, including the following:

Follow all warnings and instructions marked on

the product.
Adult setup is required.
This product is intended as an aid. It is not

a substitute for responsible and proper adult

supervision and should not be used as such.
This product is not intended for use as a medical

monitor.
Do not use this product near water. For example,

do not use it next to a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in

a wet basement or shower.
CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion

if a wrong type of battery is used for the parent

unit. Use only the supplied rechargeable battery

or replacement battery pack (BT198555/

BT298555) for the parent unit. Do not dispose of

batteries in a fire. They may explode. Dispose of

used battery according to the information in The

RBRC

seal.

Use only the adapters included with this product.

Incorrect adapter polarity or voltage can

seriously damage the product.

Baby unit power adapter: Output: 6V DC 500mA

Parent unit power adapter: Output: 6V DC 500mA.
The power adapters are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.
For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be

easily accessible.
Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.
Unplug the power cords before replacing

batteries.
Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.
Do not allow anything to rest on the power cords.

Do not install this product where the cords may

be walked on or crimped.
This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home, consult your dealer or local

power company.
Do not overload wall outlets or use an extension

cord.
Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.
This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

2.
3.

10.

11.

12.

13.

14.

15.

16.

17.

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or

heat register.
Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.
To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than specified

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.
You should test the sound reception every

time you turn on the units or move one of the

components.
Periodically examine all components for

damage.
Be aware of possible loss of privacy while using

public airwaves. Conversations may be picked

up by other nursery monitors, cordless phones,

scanners, etc.
Children should be supervised to ensure that

they do not play with the product.
The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

SAVE THESE INSTRUCTIONS

18.

19.

20.

21.

22.

23.

24.

Cautions

Use and store the product at a temperature

between 32

F and 104

Do not expose the product to extreme cold, heat

or direct sunlight. Do not put the product close to

a heating source.

Batteries should not be exposed to excessive

heat such as bright sunshine or fire.

Make sure the baby unit(s) and the adapter

cord(s) are always out of reach of the baby, at

least 3 feet away from the baby or crib, to avoid a

possible strangulation hazard.

Never place the baby unit(s) inside the baby’s crib

or playpen. Never cover the baby unit(s) or parent

unit with anything such as a towel or a blanket.

6. Other electronic products may cause

interference with your baby monitor. Try

installing your baby monitor as far away

from these electronic devices as possible:

wireless routers, radios, cellular telephones,

intercoms, room monitors, televisions,

personal computers, kitchen appliances and

cordless telephones.

Precautions for users of implanted cardiac

pacemakers
Cardiac pacemakers (applies only to digital cordless

devices):
Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless devices and implanted cardiac

pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:
Pacemaker patients

Should keep wireless devices at least six inches

from the pacemaker.
Should NOT place wireless devices directly over

the pacemaker, such as in a breast pocket, when

it is turned ON.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless devices.

Electromagnetic fields (EMF)
This VTech product complies with all standards

regarding electromagnetic fields (EMF). If handled

properly and according to the instructions in this

user’s manual, the product is safe to be used based

on scientific evidence available today.

•

The RBRC

seal

The RBRC

seal on the Ni-MH battery indicates

that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and

recycle these batteries at the end of their useful

lives, when taken out of service within the United

States and Canada.

The RBRC

program provides a convenient

alternative to placing used Ni-MH batteries into the

Ni-MH batteries into the

batteries into the

trash or municipal waste, which may be illegal in

your area.
VTech’s participation in RBRC

makes it easy for

you to drop off the spent battery at local retailers

participating in the RBRC

program or at authorized

VTech product service centers. Please call

1 (800) 8 BATTERY

for information on Ni-MH

Ni-MH

battery recycling and disposal bans/restrictions in

your area. VTech’s involvement in this program is

part of its commitment to protecting our environment

and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY®

are registered trademarks of the

Rechargeable Battery Recycling

Corporation.

FCC and IC regulations

FCC Part 15
This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment

and receiver.
Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.
Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modifications to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.
This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

•
•

•

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.
To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately 8 in (20

cm) or more. The transmitter and antenna of the

parent unit shall be held at least 1 in (2.5 cm) from

your face.
This Class B digital apparatus complies with Cana-

dian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada
This device complies with Industry Canada licence-

exempt RSS standard(s).
Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference,

including interference that may cause undesired

operation.
The term ‘’IC:‘’ before the certification/registration

number only signifies that the Industry Canada

technical specifications were met.
This product meets the applicable Industry Canada

technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation expo-

sure limits set forth for an uncontrolled environment.

The baby unit should be installed and operated

with a minimum distance of 8 in (20 cm) between

the baby unit and all persons’ body. Use of other

accessories may not ensure compliance with FCC

RF exposure guidelines. This transmitter must not be

co-located or operating in conjunction with any other

antenna or transmitter. This equipment complies

also with Industry Canada RSS-102 with respect to

Canada’s Health Code 6 for Exposure of Humans to

RF Fields.

California Energy Commission

battery charging testing mode

This baby monitor meets the California Energy

Commission (CEC) regulations for energy

consumption. Your baby monitor is set up to comply

with the energy-conserving standards right out of

the box.
Follow the instructions to install and charge the

battery. The CEC battery charging testing mode is

activated while charging.
Even if the parent unit is paired to baby units, the

CEC battery charging testing mode is activated

while it is powered off and charging.

For C_UL compliance only

Mesures de sécurité importantes

Afin de réduire les risques d’incendie, de

blessures corporelles ou d’électrocution, suivez

toujours ces mesures préventives de base
lorsque vous utilisez votre téléphone :

Lisez et comprenez bien toutes les

instructions.
Observez toutes les instructions et mises en

garde inscrites sur l’appareil.
Débranchez ce téléphone de la prise murale

avant de le nettoyer. N’utilisez pas de

nettoyeurs liquides ni en aérosol. N’utilisez

qu’un chiffon doux et légèrement humecté.
N’utilisez pas ce produit près de l’eau, tel

que près d’un bain, d’un lavabo, d’un évier

de cuisine, d’un bac de lavage ou d’une

piscine, ou dans un sous-sol humide ou

sous la douche.
Ne déposez pas ce téléphone sur un

chariot, support ou table chancelants.

L’appareil pourrait tomber et ètre

sérieusement endommagé.
Évitez d’installer le système téléphonique

dans les endroits soumis è une température

extrème, è la lumière directe du soleil ou è

proximité immédiate d’autres appareils

électriques ou électroniques. Protégez votre

téléphone contre les sources d’humidité,

la poussière, les vapeurs et les liquides

corrosifs.
Le boîtier de l’appareil est doté de fentes

et d’ouvertures d’aération situées è

l’arrière ou en dessous. Afin d’empècher la

surchauffe, ces ouvertures ne doivent pas

ètre obstruées en plaçant l’appareil sur un

lit, divan, tapis ou autre surface similaires.

Ne placez pas cet appareil è proximité

d’un élément de chauffage ni d’une plinthe

électrique. De plus, ne l’installez pas dans

une unité murale ou un cabinet fermé qui ne

possède pas d’aération adéquate.
Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur les étiquettes

de l’appareil. Si vous ne connaissez pas le

voltage de votre maison, consultez votre

marchand ou votre fournisseur d’électricité.
Ne déposez rien sur le cordon

d’alimentation. Installez cet appareil dans

un endroit sécuritaire, lè oè personne ne

pourra trébucher sur la ligne d’alimentation

ni le cordon téléphonique modulaire.
N’insérez jamais d’objets è travers les

fentes et ouvertures de cet appareil, car ils

10.

pourraient toucher è des points de tension

dangereux ou court-circuiter des pièces, ce

qui constituerait un risque d’incendie ou

d’électrocution. N’échappez pas de liquides

dans l’appareil.
Afin de réduire les risques d’électrocution,

ne démontez pas l’appareil, mais apportez-

le plutôt è un centre de service qualifié s’il

doit ètre réparé. En enlevant le couvercle,

vous vous exposez è des tensions

dangereuses ou autres dangers similaires.

Un remontage inadéquat peut ètre è l’origine

d’une électrocution lors d’une utilisation

ultérieure de l’appareil. Débranchez

l’appareil avant de procéder au nettoyage.

Utilisez un chiffon humide et doux.
Ne surchargez pas les prises de courant et

les rallonges.
Débranchez cet appareil de la prise

de courant et communiquez avec le

département de service è la clientèle de

VTech dans les cas suivants:

Lorsque le cordon d’alimentation est

endommagé ou écorché.
Si du liquide a été échappé dans

l’appareil.
Si l’appareil a été exposé è une source

d’humidité telle que la pluie ou l’eau.
Si le produit ne fonctionne pas
normalement en respectant les

instructions de fonctionnement.

Réglez uniquement les commandes

indiquées dans le les instructions

de fonctionnement. Les réglages

incorrects des autres commandes

pourraient provoquer un dommage qui

pourrait exiger un travail exhaustif de

la part d’un technicien autorisé afin de

rétablir le fonctionnement normal de

l’appareil.
Si le produit a été échappé et que

le socle et/ou le combiné a été

endommagé.
Si le produit affiche une nette

diminution de sa performance.

14. Évitez d’utiliser un téléphone (autre qu’un

sans fil) pendant un orage. Les éclairs

peuvent ètre è l’origine d’une électrocution.

15. N’utilisez pas le téléphone pour rapporter

une fuite de gaz è proximité de la fuite. En

certaines circonstances, une flammèche

pourrait ètre provoquée lorsque l’adaptateur

est branché è une prise de courant, ou

lorsque le combiné est déposé sur le socle.

Ceci est un événement commun associé

è la fermeture d’un circuit électrique.

L’utilisateur ne devrait pas brancher le

téléphone è une prise de courant, et ne

11.

12.

13.

•

•
•

•

devrait pas déposer le combiné chargé

sur le socle, si le téléphone se trouve è

proximité d’un endroit comportant des

concentrations de gaz inflammables, è

moins que la ventilation soit adéquate.

Une flammèche dans un tel endroit

pourrait provoquer un incendie ou une

explosion. De tels environnements peuvent

comprendre: des endroits oè l’on utilise

de l’oxygène médical sans ventilation

adéquate; des gaz industriels (dissolvants

de nettoyage, des vapeurs d’essence,

etc.); une fuite de gaz naturel, etc.

16. Ne placez que le combiné de votre

téléphone près de votre oreille lorsqu’en

mode de conversation.

17. Ces adaptateurs ont été conçus pour ètre

orientés en position verticale ou montés au

sol. Les broches ne sont pas conçues pour

maintenir l’adaptateur en place si celui-ci

est barnché dans une prise au plafond ou

sous une table/ armoire.

CONSERVEZ CES INSTRUCTIONS

Pile

MISE EN GARDE : N’utilisez que la pile

incluse.

Ne jetez pas la pile au feu. Vérifiez les

instructions spécifiques de mise aux rebus

auprès des autorités locales.

N’ouvrez pas et ne mutilez pas la pile.

L’électrolyte qui s’en échapperait est

corrosif et pourrait causer des brèlures

ou des blessures aux yeux ou è la peau.

L’électrolyte est toxique si avalé.

Soyez prudents lorsque vous manipulez

les piles afin d’éviter les courts-circuits

provoqués par des matériaux conducteurs.

Rechargez la pile incluse avec cet appareil,

selon les instructions et limites spécifiées

dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans

l’organisme
Les simulateurs cardiaques (s’applique

uniquement aux téléphones numériques sans

fil):
L’organisme ‘Wireless Technology Research,

LLC (WTR)’, une firme de recherche

indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les

téléphones sans fil portatifs et les stimulateurs

cardiaques implantés dans l’organisme.

Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la firme WTR

recommande aux médecins:
Avis aux détenteurs de stimulateurs

cardiaques

•

Ils doivent tenir le téléphone sans fil è

une distance d’au moins six pouces du

stimulateur cardiaque.

Ils ne doivent PAS placer le téléphone sans

fil directement sur le stimulateur cardiaque,

tel que dans une poche de chemise, lorsque

celui-ci est en marche.

Ils doivent utiliser le téléphone sans fil en

l’appuyant sur l’oreille qui se trouve dans la

direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a

pas identifié de risque pour les détenteurs de

simulateurs cardiaques causés par les gens

qui utilisent un téléphone sans fil è proximité de

ceux-ci.

À propos des téléphones sans fil

Alimentation électrique: Les mèmes

caractéristiques qui constituent des

avantages pour les téléphones sans fil

affichent également des restrictions. Les

appels téléphoniques sont transmis entre

le combiné sans fil et le socle par le biais

d’ondes radio ; il y a donc la possibilité que

vos conversations téléphoniques sans fil

soient interceptées par des équipements de

réception radio se trouvant dans la portée

du combiné sans fil. Pour cette raison, vous

ne devez pas percevoir les communications

téléphoniques sans fil comme étant aussi

confidentielles.
Alimentation électrique: Le socle de ce

téléphone sans fil doit ètre branché è une

prise électrique fonctionnelle. La prise

électrique ne doit pas ètre contrôlée par un

interrupteur mural. Les appels ne pourront

pas ètre effectués du combiné sans fil si le

socle est débranché ou mis hors tension ou

si le courant est coupé.
Possibilité d’interférences aux
téléviseurs: Certains téléphones sans fil
fonctionnent sur des fréquences pouvant
causer des interférences aux téléviseurs
et aux magnétoscopes. Pour réduire ou
prévenir de telles interférences, ne placez
pas le socle du téléphone sans fil près ou
sur un téléviseur ou magnétoscope. S’il
y a présence de parasites, il est conseillé
d’éloigner le téléphone sans fil du téléviseur
ou du magnétoscope afin de réduire
possiblement les interférences.
Piles rechargeables: Manipulez les piles
avec soin afin de ne pas les court-circuiter
avec des bagues, bracelets ou clés. Les
piles ou le conducteur peut surchauffer et
causer des blessures. Respectez la polarité

•

adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure

métallique de nickel: Jetez ces blocs-piles

de manière écologique et sécuritaire. Ne les

incinérez pas et ne les percez pas. Tel que

les autres piles de ce type, elles pourraient

dégager une matière toxique qui peut

causer des blessures corporelles si elles
sont brèlées ou percées.

•

aujourd’hui.

Limited warranty

What does this limited warranty cover?
The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during

the limited warranty period (“Materially Defective

Product”)?
During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace the

Product, we may replace it with a new or refurbished

Product of the same or similar design. We will

retain defective parts, modules, or equipment.

Repair or replacement of the Product, at VTech’s

option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in

working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?
The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either (a)

90 days from the date the repaired or replacement

Product is shipped to you or (b) the time remaining

on the original one-year warranty; whichever is

longer.

What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, fire, water or other

liquid intrusion; or

2. Product that has been damaged due to repair,

alteration or modification by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced

is caused by signal conditions, network reliability,

or cable or antenna systems; or

4. Product to the extent that the problem is caused

by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered

illegible; or

6. Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products

used for rental purposes); or

7. Product returned without a valid proof of purchase

(see item 2 on the next page); or

8. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?
To obtain warranty service in the USA, please visit

our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls

and features may save you a service call.
Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery or

handling charges incurred in the transport of the

Product(s) to the service location. VTech will return

repaired or replaced Product under this limited

warranty. Transportation, delivery or handling

charges are prepaid. VTech assumes no risk for

damage or loss of the Product in transit. If the Product

failure is not covered by this limited warranty, or proof

of purchase does not meet the terms of this limited

warranty, VTech will notify you and will request that

you authorize the cost of repair prior to any further

repair activity. You must pay for the cost of repair and

return shipping costs for the repair of Products that

are not covered by this limited warranty.

What must you return with the Product to get

warranty service?

Return the entire original package and contents

including the Product to the VTech service

location along with a description of the malfunction

or difficulty; and
Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model)

and the date of purchase or receipt; and

Provide your name, complete and correct mailing

address, and telephone number.

Other limitations
This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to this

Product. VTech provides no other warranties for this

Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There

are no other express warranties. No one is authorized

to make modifications to this limited warranty and you

should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you

specific legal rights, and you may also have other

rights, which vary from state to state or province to

province.
Limitations: Implied warranties, including those of

fitness for a particular purpose and merchantability (an

unwritten warranty that the Product is fit for ordinary

use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on

how long an implied warranty lasts, so the above

limitation may not apply to you. In no event shall

VTech be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost profits or revenue, inability to use

the Product or other associated equipment, the cost

of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Technical specifications

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

Baby unit: 2405 - 2475 MHz

Parent unit: 2405 - 2475 MHz

Channels

LCD

2.8” Color LCD

(WQVGA 320x240 pixel)

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirements

Parent unit: 3.6V Ni-MH battery
Baby unit power adapter:

Output: 6V DC @ 500mA
Parent unit power adapter:

Output: 6V DC @ 500mA