Visonic Inc. MCPIR3000 사용자 설명서

DE3637

1

K

K

K

K-980

-980

-980

-980MCW

MCW

MCW

MCW

1

11

1. INTRODUCTION

. INTRODUCTION

. INTRODUCTION

. INTRODUCTION

The K-980MCW is a pet-immune, fully supervised ultra low-
current wireless PIR that incorporates a PowerCode transmitter.
Both transmitter and detector circuits are powered by an
on-board, long life 3.6 V Lithium battery.
As a pet immune motion detector, the K-980MCW utilizes TSI™
(Target Specific Imaging) technology that ensures immunity to
pets weighing up to 36 kg (80 lb).  
As a supervised wireless detector, the K-980MCW has a 24-bit
ID code, randomly selected in the factory from over 16 million
possible combinations. Compatible PowerCode receivers are
designed to "learn" specific IDs and respond only to them.
Following detection of a human intruder, the K-980MCW triggers
the on-board transmitter which transmits its specific PowerCode
ID followed by an  alarm signal and status designators for
tampering and battery condition. Alarm and other data are thus
forwarded to the alarm control panel or to a head-end computer,
depending on the type of system in which the detector is used.
After triggering the transmitter, the K-980MCW inhibits itself to

save battery power. The detector reverts to the ready state 2

minutes after the last movement has been detected. An LED/

WALK-TEST jumper is used to override the 2-minute rearm timer

during walk testing.
Since messages transmitted by

the K-980MCW might collide with

messages transmitted by other

PowerCode transmitters, an anti-

collision transmission sequence is

used.
A programmable pulse counter is

included in the unit for maximum

immunity against false alarms.
A periodic test transmission for

supervision purposes takes place

automatically once an hour. The

receiver is thus informed that the

particular detector is taking an

active part in the wireless

network.

2

22

2. SPECIFICATIONS

. SPECIFICATIONS

. SPECIFICATIONS

. SPECIFICATIONS

OPTICAL  
Max. Coverage Range: 12 x 12 m (40 x 40 ft) / 90°
Pet Immunity: Animals weighing up to 36 kg (80 lb).
Vertical Adjustment: 3-position adjustment scale: 1.8 m (6 ft),

2.1 m (7 ft) and 2.4 m (8 ft).
ELECTRICAL
Battery Type: 3.6 Volt lithium thionyl chloride (LiSOCl

2

) battery,

size 1/2AA, Tadiran TL-5902 or equivalent.
Nominal Battery Capacity: 1.2 Ah
Standby Current Drain: 0.015 mA.
Transmit Current Drain: 9.5 mA (including LED)
Battery Life (with LED on)

@ 10 transmissions per day: about 7 years
@ 50 transmissions per day: about 5 years

LED:  Lights for 2 seconds upon transmission and upon motion

detection in the walk test mode.
Detector: Dual-element low-noise pyroelectric sensor.
Pulse Counter: Programmable to 1, 3 or 5 pulses.
Rearm Timer: 2 minutes after the last alarm; timer disabled in the

walk test mode.

Frequency (MHz): 315, 404, 418, 433.92 or other frequencies

according to local requirements.
Transmission Sequence: 3 data bursts at variable intervals within

3 seconds.
Encoding: 24-bit ID, over 16 million possible combinations.
Total Message Length: 36 bits
Battery Supervision: Automatic reporting of low-battery status

with each alarm and with periodic autotest.
Tamper Alert: Reported at 3-minute intervals, until the tamper

switch is restored.
ENVIRONMENTAL

Operating Temperature: -10

°

 to 50

°

C (14

°

 to 122

°

F).

Storage Temperature: -20

°

 to 60

°

C (-4

°

F to 140

°

F).

RFI Protection: > 30 V/m up to 1000 MHz
Compliance with Standards: FCC Part 15, ETS300-220 and

MPT1349
PHYSICAL
Size (H x W x D): 117  x 65 x 47 mm (4-5/8 x 2-9/16 x 1-7/8 in.).
Color:  White.
Weight: 97 g  (3.4 oz) without bracket. 112 g  (4 oz) with bracket.

3

33

3. INSTALLATION

. INSTALLATION

. INSTALLATION

. INSTALLATION

3.1 Installation Hints

Do not aim at heat sources

Mount on solid, stable surfaces

Do not expose to air drafts

Do not install outdoors