Casablanca Fan Company CASA11T 사용자 설명서

The 

1

2

0

4

3

 power button is normally left in the on 

position. always turn the power off during cleaning or 
servicing the fan and during thunderstorms. it is also 
used to exit or enter additional programs.
The 

1

2

0

4

3

 power button must be left on to retain a 

previously set fan speed or light level.

1

2

0

4

3

There are five individual speed settings 
for the fan. Each speed is indicated by the 
number on the controller and an audible tone 
for each speed.

To select the desired fan speed:
Press the number on the controller 
corresponding to the speed desired. 4 is high, 
3 medium, 2 low, 1 ultra-low, and 0 is off.

1

2

0

4

3

Note: It is normal for the fan to start 

in the "High" position from "Off" 

before  changing  to  the  selected 

speed.

The direction of airflow can be changed from 
downward to upward or from upward to downward.

To reverse the airflow:
1.  Make sure the fan is on and blades are turning.
2.  Press the 

1

2

0

4

3

 reverse button. You will hear a 

series of clicks from the fan as it speeds up 
before coming to a stop and changing direction. 

1

2

0

4

3

To turn the lights off and on, press and 

release the 

1

2

0

4

3

 button for either the up or 

down lights for less than one second.

To dim either the up or down light, Press 

and hold the 

1

2

0

4

3

 button for either the up or 

down light for more than 1 second. The light 
will come on at the last brightness setting 
and increase in brightness until full power is 
reached, then start dimming until the lowest 
setting is reached. This cycle will repeat until 
you release the light button.

1

2

0

4

3

Up Light

Down Light

Note: The dimming feature will only 

work as long as the dimming feature 

remains active. See "Operation CFL 

mode".

Your fan has the ability to disable the 
dimming feature to allow the use of CFL 
bulbs. 

To activate CFL mode:
1.  Turn the fan off by pressing the 

1

2

0

4

3

 

power button.

2.  allow the fan to remain off for at least 5 seconds.
3.  Press the  power button again to restore power to the fan.
4.  immediately press and hold the "1" and "3" buttons for at least 5 seconds. 

The fans lights will go to 100% brightness and the dimming function will 
be disabled.

To cancel CFL mode:
5.  Turn the fan off by pressing the 

1

2

0

4

3

 power button.

6.  allow the fan to remain off for at least 5 seconds.
7.  Press the  power button again to restore power to the fan.
8.  immediately press and hold the "2" and "4" buttons for at least 5 seconds. 

The fans lights will dim  to 50% brightness and the dimming function will 
be enabled. Press and hold the light buttons until the desired dimmer 
setting is reached.

Caution: CFL bulbs will not 
function properly when 
dimmed, which may result 
in flickering or reduced bulb 
life.

Programmed into every Direct-Touch fan is 
an automatic Demonstration Program. it can 
be used to fully demonstrate and test the 
operation of the fan.

To enter the demonstration program:
1.  Turn the 

1

2

0

4

3

 power button off for at least 

5 seconds. This will clear the fan memory ready for programming.

2.  Turn the 

1

2

0

4

3

 power button on.

3.  immediately hold the "0" button for at least 5 seconds. 
a multi-tone signal will verify the start of the test program. The fan and lights 
will go through a series of changing fan speeds, reversing the fan operation 
mode, turning off/on, and dimming the lights. 

The complete cycle lasts slightly over one minute. it will continue to repeat 
until the 

1

2

0

4

3

 is turned off for more than five seconds, cancelling the program.

note: With CFL mode active, 
the lights will not dim.

The Safe-Exit Program gives you about thirty 
seconds of light when you turn the lights off, 
enabling you to exit your home before the lights go 
out. To enter the Safe-Exit Program:
1.  Press the 

1

2

0

4

3

 power button off for at least five 

seconds.

2.  Turn the Power on. immediately press and 

hold the "4" button for 5 seconds. When a 
light button is pressed, an audio tone and series of lights blinking will 
indicate the program is active. When CFL mode is disabled, the Lights will 
stay on at 50% brightness for 20 seconds then decrease in intensity for 30 
seconds then turn off.

3.  With CFL mode active, the lights will turn off after 30 seconds.
4.  To cancel the Safe-Exit Program, press the 

1

2

0

4

3

 power button and leave off 

for five seconds.

The Light-Minder Program automatically turns OFF 
the fan mounted lights after two hours. To enter the 
Light-Minder Program: 

1.  To operate the lights for Light Minder Program 

– Turn the 

1

2

0

4

3

 power button off for at least 5 

seconds.

2.  Turn the 

1

2

0

4

3

 on. immediately press and 

hold the "1" button for 5 seconds. a series of 
tones will be heard through the piezo-buzzer 
indicating the command has been accepted. 
Once the lights turn on, they will automatically 
turn off after 2 hours.

3.  Light operation still remains normal, if you leave the room and turn OFF 

the lights, the lights will blink to indicate the Light Minder command has 
been accepted. The lights will stay on for 2 hours and then begin to dim. 
after thirty seconds have elapsed, the lights will turn completely off. in 
CFL Mode, the lights will not dim, but shut off after 2 hours.

4.  To cancel the Light Minder Program, press the 

1

2

0

4

3

 power button and 

leave off for five seconds.

1.  To operate the Home-Safe Program – 

Turn the 

1

2

0

4

3

 power button off for at 

least 5 seconds.

2.  Turn the 

1

2

0

4

3

 on. immediately press and 

hold the "3" button for 5 seconds. a 
series of tones will be heard through the 
piezo-buzzer indicating the command 
has been accepted.

 Note: This program overrides all manual control of  

 lights and fan. 

3.  The lights will automatically cycled on and off in a controlled sequence as 

follows: On 1 hour, OFF ½ hour, On 2 hours, OFF 1 hour, On ½ hour then 
OFF 2 hours. This seven hour pattern will repeat continuously so that a 
different pattern of lighting is seen each day of the week.

4.  4) To cancel the Home-Safe Program, press the 

1

2

0

4

3

 Button OFF for five 

seconds.

The Fan-Minder feature will add to your comfort when used 
in the bedroom. The program reduces the speed of the fan 
each two-hour interval to compensate for cooling night air. 

1.  To operate the lights for Light Minder Program – Turn 

the 

1

2

0

4

3

 power button off for at least 5 seconds.

2.  Turn the 

1

2

0

4

3

 on. immediately press and hold the "2" 

button for 5 seconds. a series of tones will be heard 
through the piezo-buzzer indicating the command 
has been accepted. Once the lights turn on, they will 
automatically turn off after 2 hours.

3.  The fan will respond with three descending tones. a 

timer is now initiated and the fan will reduce one speed for each two-hour 
interval. The fan will not, however, descend below the first or the lowest 
speed.

4.  You may increase the fan speed by pressing and holding any of the fan speed 

buttons until the desired speed is reached, then release it. The fan will again 
reduce one speed for each 2 hour interval.

5.  To cancel the Fan-Minder Program, turn the 

1

2

0

4

3

 OFF for 5 seconds. 

*This device complies with part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) This device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference that may cause undesired 

operation.
 *This device complies with RSS-GEN IC: Operation is subject to the following two 

conditions: (1) this device may not cause interference, and (2) this device must accept any 

interference, including interference that may cause undesired operation of the device.
 *Any alteration of this product, either intentional or unintentional, not expressly approved 

by the manufacturer could result in operation failure of the device, inability to gain 

assistance from our technical team, or manufacturer refusing warranty support.