Casablanca Fan Company CASA11T 사용자 설명서
operation
OPERATION SPEED CONTROL
OPERATION REvERSING AIRFLOW
OPERATION LIGHTS
AUTOmATIC DEmONSTRATION PROGRAm
OPERATION HOmE-SAFE
®
PROGRAm
OPERATION FAN-mINDER
™
PROGRAm
The
1
2
0
4
3
power button is normally left in the on
position. always turn the power off during cleaning or
servicing the fan and during thunderstorms. it is also
used to exit or enter additional programs.
The
servicing the fan and during thunderstorms. it is also
used to exit or enter additional programs.
The
1
2
0
4
3
power button must be left on to retain a
previously set fan speed or light level.
1
2
0
4
3
There are five individual speed settings
for the fan. Each speed is indicated by the
number on the controller and an audible tone
for each speed.
for the fan. Each speed is indicated by the
number on the controller and an audible tone
for each speed.
To select the desired fan speed:
Press the number on the controller
corresponding to the speed desired. 4 is high,
3 medium, 2 low, 1 ultra-low, and 0 is off.
Press the number on the controller
corresponding to the speed desired. 4 is high,
3 medium, 2 low, 1 ultra-low, and 0 is off.
1
2
0
4
3
Note: It is normal for the fan to start
in the "High" position from "Off"
before changing to the selected
speed.
The direction of airflow can be changed from
downward to upward or from upward to downward.
downward to upward or from upward to downward.
To reverse the airflow:
1. Make sure the fan is on and blades are turning.
2. Press the
1. Make sure the fan is on and blades are turning.
2. Press the
1
2
0
4
3
reverse button. You will hear a
series of clicks from the fan as it speeds up
before coming to a stop and changing direction.
before coming to a stop and changing direction.
1
2
0
4
3
To turn the lights off and on, press and
release the
1
2
0
4
3
button for either the up or
down lights for less than one second.
To dim either the up or down light, Press
and hold the
1
2
0
4
3
button for either the up or
down light for more than 1 second. The light
will come on at the last brightness setting
and increase in brightness until full power is
reached, then start dimming until the lowest
setting is reached. This cycle will repeat until
you release the light button.
will come on at the last brightness setting
and increase in brightness until full power is
reached, then start dimming until the lowest
setting is reached. This cycle will repeat until
you release the light button.
1
2
0
4
3
Up Light
Down Light
Note: The dimming feature will only
work as long as the dimming feature
remains active. See "Operation CFL
mode".
Your fan has the ability to disable the
dimming feature to allow the use of CFL
bulbs.
dimming feature to allow the use of CFL
bulbs.
To activate CFL mode:
1. Turn the fan off by pressing the
1. Turn the fan off by pressing the
1
2
0
4
3
power button.
2. allow the fan to remain off for at least 5 seconds.
3. Press the power button again to restore power to the fan.
4. immediately press and hold the "1" and "3" buttons for at least 5 seconds.
3. Press the power button again to restore power to the fan.
4. immediately press and hold the "1" and "3" buttons for at least 5 seconds.
The fans lights will go to 100% brightness and the dimming function will
be disabled.
be disabled.
To cancel CFL mode:
5. Turn the fan off by pressing the
5. Turn the fan off by pressing the
1
2
0
4
3
power button.
6. allow the fan to remain off for at least 5 seconds.
7. Press the power button again to restore power to the fan.
8. immediately press and hold the "2" and "4" buttons for at least 5 seconds.
7. Press the power button again to restore power to the fan.
8. immediately press and hold the "2" and "4" buttons for at least 5 seconds.
The fans lights will dim to 50% brightness and the dimming function will
be enabled. Press and hold the light buttons until the desired dimmer
setting is reached.
be enabled. Press and hold the light buttons until the desired dimmer
setting is reached.
Caution: CFL bulbs will not
function properly when
dimmed, which may result
in flickering or reduced bulb
life.
function properly when
dimmed, which may result
in flickering or reduced bulb
life.
oPeration cFl Mode
Programmed into every Direct-Touch fan is
an automatic Demonstration Program. it can
be used to fully demonstrate and test the
operation of the fan.
an automatic Demonstration Program. it can
be used to fully demonstrate and test the
operation of the fan.
To enter the demonstration program:
1. Turn the
1. Turn the
1
2
0
4
3
power button off for at least
5 seconds. This will clear the fan memory ready for programming.
2. Turn the
1
2
0
4
3
power button on.
3. immediately hold the "0" button for at least 5 seconds.
a multi-tone signal will verify the start of the test program. The fan and lights
will go through a series of changing fan speeds, reversing the fan operation
mode, turning off/on, and dimming the lights.
a multi-tone signal will verify the start of the test program. The fan and lights
will go through a series of changing fan speeds, reversing the fan operation
mode, turning off/on, and dimming the lights.
The complete cycle lasts slightly over one minute. it will continue to repeat
until the
until the
1
2
0
4
3
is turned off for more than five seconds, cancelling the program.
note: With CFL mode active,
the lights will not dim.
the lights will not dim.
oPeration SaFe-exit®
The Safe-Exit Program gives you about thirty
seconds of light when you turn the lights off,
enabling you to exit your home before the lights go
out. To enter the Safe-Exit Program:
1. Press the
seconds of light when you turn the lights off,
enabling you to exit your home before the lights go
out. To enter the Safe-Exit Program:
1. Press the
1
2
0
4
3
power button off for at least five
seconds.
2. Turn the Power on. immediately press and
hold the "4" button for 5 seconds. When a
light button is pressed, an audio tone and series of lights blinking will
indicate the program is active. When CFL mode is disabled, the Lights will
stay on at 50% brightness for 20 seconds then decrease in intensity for 30
seconds then turn off.
light button is pressed, an audio tone and series of lights blinking will
indicate the program is active. When CFL mode is disabled, the Lights will
stay on at 50% brightness for 20 seconds then decrease in intensity for 30
seconds then turn off.
3. With CFL mode active, the lights will turn off after 30 seconds.
4. To cancel the Safe-Exit Program, press the
4. To cancel the Safe-Exit Program, press the
1
2
0
4
3
power button and leave off
for five seconds.
Safe-Exit
The Light-Minder Program automatically turns OFF
the fan mounted lights after two hours. To enter the
Light-Minder Program:
the fan mounted lights after two hours. To enter the
Light-Minder Program:
1. To operate the lights for Light Minder Program
– Turn the
1
2
0
4
3
power button off for at least 5
seconds.
2. Turn the
1
2
0
4
3
on. immediately press and
hold the "1" button for 5 seconds. a series of
tones will be heard through the piezo-buzzer
indicating the command has been accepted.
Once the lights turn on, they will automatically
turn off after 2 hours.
tones will be heard through the piezo-buzzer
indicating the command has been accepted.
Once the lights turn on, they will automatically
turn off after 2 hours.
3. Light operation still remains normal, if you leave the room and turn OFF
the lights, the lights will blink to indicate the Light Minder command has
been accepted. The lights will stay on for 2 hours and then begin to dim.
after thirty seconds have elapsed, the lights will turn completely off. in
CFL Mode, the lights will not dim, but shut off after 2 hours.
been accepted. The lights will stay on for 2 hours and then begin to dim.
after thirty seconds have elapsed, the lights will turn completely off. in
CFL Mode, the lights will not dim, but shut off after 2 hours.
4. To cancel the Light Minder Program, press the
1
2
0
4
3
power button and
leave off for five seconds.
liGHt-Minder® ProGraM
Light-Minder
1. To operate the Home-Safe Program –
Turn the
1
2
0
4
3
power button off for at
least 5 seconds.
2. Turn the
1
2
0
4
3
on. immediately press and
hold the "3" button for 5 seconds. a
series of tones will be heard through the
piezo-buzzer indicating the command
has been accepted.
series of tones will be heard through the
piezo-buzzer indicating the command
has been accepted.
Note: This program overrides all manual control of
lights and fan.
3. The lights will automatically cycled on and off in a controlled sequence as
follows: On 1 hour, OFF ½ hour, On 2 hours, OFF 1 hour, On ½ hour then
OFF 2 hours. This seven hour pattern will repeat continuously so that a
different pattern of lighting is seen each day of the week.
OFF 2 hours. This seven hour pattern will repeat continuously so that a
different pattern of lighting is seen each day of the week.
4. 4) To cancel the Home-Safe Program, press the
1
2
0
4
3
Button OFF for five
seconds.
The Fan-Minder feature will add to your comfort when used
in the bedroom. The program reduces the speed of the fan
each two-hour interval to compensate for cooling night air.
in the bedroom. The program reduces the speed of the fan
each two-hour interval to compensate for cooling night air.
1. To operate the lights for Light Minder Program – Turn
the
1
2
0
4
3
power button off for at least 5 seconds.
2. Turn the
1
2
0
4
3
on. immediately press and hold the "2"
button for 5 seconds. a series of tones will be heard
through the piezo-buzzer indicating the command
has been accepted. Once the lights turn on, they will
automatically turn off after 2 hours.
through the piezo-buzzer indicating the command
has been accepted. Once the lights turn on, they will
automatically turn off after 2 hours.
3. The fan will respond with three descending tones. a
timer is now initiated and the fan will reduce one speed for each two-hour
interval. The fan will not, however, descend below the first or the lowest
speed.
interval. The fan will not, however, descend below the first or the lowest
speed.
4. You may increase the fan speed by pressing and holding any of the fan speed
buttons until the desired speed is reached, then release it. The fan will again
reduce one speed for each 2 hour interval.
reduce one speed for each 2 hour interval.
5. To cancel the Fan-Minder Program, turn the
1
2
0
4
3
OFF for 5 seconds.
*This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
*This device complies with RSS-GEN IC: Operation is subject to the following two
*This device complies with RSS-GEN IC: Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
*Any alteration of this product, either intentional or unintentional, not expressly approved
*Any alteration of this product, either intentional or unintentional, not expressly approved
by the manufacturer could result in operation failure of the device, inability to gain
assistance from our technical team, or manufacturer refusing warranty support.