Philips Lighting Company 322202190511 사용자 설명서
Unpack
Remote
Control
3 AAA
Batteries
Plug with cord
(is packed at the bottom)
Support
AA
A
A
A
A
A
A
A
Top Side
LivingColors
LivingColors
Safety Instructions
Keep the plug and LivingColors away from liquids and humidity.
• LivingColors is for indoor use only. Do not use in wet locations, e.g. bathrooms or outdoors.
• LivingColors is not a toy designed to be played with by children.
• Do not place on hot surfaces.
• For safety reasons and under the terms of the warranty the LivingColors and plug must not be opened.
• Only use the plug supplied with the charger: using an plug with the wrong polarity or current can
damage your LivingColors.
• LivingColors is for indoor use only. Do not use in wet locations, e.g. bathrooms or outdoors.
• LivingColors is not a toy designed to be played with by children.
• Do not place on hot surfaces.
• For safety reasons and under the terms of the warranty the LivingColors and plug must not be opened.
• Only use the plug supplied with the charger: using an plug with the wrong polarity or current can
damage your LivingColors.
Extend the LivingColors Possibilities
Fault Tracing
The LivingColors will bring you a colorful world of opportunities.
1. If, however, you face one of the exceptional situations where :
LivingColors is not providing light,
LivingColors is not providing light,
•
check your batteries in the Remote Control
•
check the connections
•
check the plug
2. Is LivingColors still not working up to standards, please call 1-800-555-0050
(also see Warranty and Service).
(also see Warranty and Service).
Getting Started
0
1
On/off
Color tuning
White balance
Dimming
LivingColors
Remote control
0
1
Open the battery compartment of the Remote Control by sliding the button
at the back.
at the back.
Insert the 3 AAA batteries (+ and – as indicated).
Place LivingColors at a selected location on a level, stable surface. Depending on the
surface, you could consider using the support (A) especially designed for LivingColors.
surface, you could consider using the support (A) especially designed for LivingColors.
Direct LivingColors towards the wall, and insert the plug into the wall socket.
A
LivingColors will show a short introduction to the color possibilities
(this is normal).
(this is normal).
Switch LivingColors on by pushing the
1
(on) on the on/off button.
Create your own ambience by:
1. Touching the desired color on the touch ring,
1. Touching the desired color on the touch ring,
Move a finger over the touch ring for refining the color.
2. Deep full color through to white
Push the white balance button, for a shorter or longer time, on A ( )
for a deep color or on B ( ) for more pastel through to white.
3. Dimming
Increase (
) or decrease (
) the amount of light via the
Dimming Button.
Switch off LivingColors by pushing the
0
(off) on the on/off button.
LivingColors will remember the last setting.
0
1
A
B
0
1
Up to 6 LivingColors can be connected.
Independently:
1) Use more LivingColors independently with it’s own remote control.
1) Use more LivingColors independently with it’s own remote control.
They will show different colors each.
Together
2) Operate 2 (or more) LivingColors with one remote control.
2) Operate 2 (or more) LivingColors with one remote control.
They will show similar colors.
• Hold the remote control with a finger on the “on” button, close to the
• Hold the remote control with a finger on the “on” button, close to the
front of LivingColors.
• LivingColors will flash 3 times, as a confirmation for being connected.