Williams Sound DLT300 사용자 설명서

14

Press the MENU button twice for the M1 and M2, once for GSTs. The address for the DLT will be displayed for two seconds. 

NOTE: Every DLT MuST have its own address and all must be assigned to the same group.

“Groups” apply to 2-way Mode only.

1. With the DLT powered ON, push and hold the Group button 

  until the GROUP indicator on the screen 

starts blinking and the light above the Group button comes on (Figure 5).

2. Change groups by pushing the Up button 

 or the Down button 

 .  If no buttons are pushed, the 

Quick Group Change feature will time out after 5 seconds.

3. Push the Group button 

 once to exit the Quick Group Change function, or wait for 5 seconds.

This feature allows the user to choose between Push and Latch (PnL) or Push to Talk (Ptt). The default is PnL.  
In PnL mode, when the TALK button 

 is pressed and released, it stays in talk mode until the TALK 

button is pressed and released again.  
In Ptt mode, the TALK button must be held down while speaking, and when released, it shuts off.
The DLT must be set up as a Guest unit, in 2-way mode, prior to performing these steps.
1. With the DLT powered ON, press and hold the Up button 

 and the Down button 

  

simultaneously for 2 seconds to enter programming mode.  
2. Push the Power/Menu button until the TALK indicator is flashing and either “PnL” is or “Ptt” is 

displayed. (Figure 6).
3. Use either of the -/+ buttons  

  to switch between “PnL” and “Ptt”

4. Press and hold the Up button  

  and the Down button 

  simultaneously for 2 seconds to exit programming mode. 

This gives the user the ability to change the volume of their own voice heard in the headset (side tone). 
1. With the DLT powered ON, press and hold the Up button 

 and the Down button 

  simultaneously 

for 2 seconds to enter programming mode.  
2. Push the Power/Menu button until “St:” is displayed.  See Figure 7.
3. Use either of the -/+ buttons  

  to choose between Stt:0 (Off), St:1 (-6dB) (default), or St:2 

(-12dB).
4. Press and hold the Up button 

 and the Down button 

  simultaneously for 2 seconds to exit 

programming mode. 

The user hears an audible “double-beep” sound when the TALK button is turned off.  This is heard in the headset of the user only; it is 

not transmitted. On the DLT, as the headset volume is increased, the beep volume will increase until the headset volume reaches 37, 

then the beep volume will stop increasing. (Note: On the DLT 100 the beep volume continued to get louder as the headphone volume 

was increased, with no limit.)

Secure Key Code fig. 1

Original (save)

Secure Key Code fig. 2

SLOC fig. 3

Tone Control  fig. 4

Quick Group Change  fig. 5

Ptt & PnL  fig. 6

Ptt & PnL  fig. 6

Side Tone fig. 7

A530

Secure Key Code fig. 1

Original (save)

Secure Key Code fig. 2

SLOC fig. 3

Tone Control  fig. 4

Quick Group Change  fig. 5

Ptt & PnL  fig. 6

Ptt & PnL  fig. 6

Side Tone fig. 7

A530

Secure Key Code fig. 1

Original (save)

Secure Key Code fig. 2

SLOC fig. 3

Tone Control  fig. 4

Quick Group Change  fig. 5

Ptt & PnL  fig. 6

Ptt & PnL  fig. 6

Side Tone fig. 7

A530

Secure Key Code fig. 1

Original (save)

Secure Key Code fig. 2

SLOC fig. 3

Tone Control  fig. 4

Quick Group Change  fig. 5

Ptt & PnL  fig. 6

Ptt & PnL  fig. 6

Side Tone fig. 7

A530