Shure PG2A 사용자 설명서
C
ongratulations on
purchasing your Shure
Performance Gear Wireless
system. Shure professional
audio products deliver
legendary sound quality,
stage-proven durability and
hassle-free setup for worry-free
performance.
Performance Gear Wireless
systems are available in a
variety of configurations for
handheld, guitar, headset, and
presentation applications
presentation applications
.
Startup
channel
ready
audio
Internal Diver
Busy Indicator
When selecting channels,
a flashing dash indicates
interference from television
broadcasts, electronic devices
or other wireless systems.
CHANNEL
6
MUT
E
channel
mute
channel
ready
audio
Internal Antenna Diversity
channel
mute
channel
mute
Accessing Gain Switch
channel
mute
Testing Audio
Talk or sing into the
microphone or play
instrument.
0dB For instrument or quiet to normal vocal performance (default).
–10dB Use if audio is distorted due to high vocal or instrument levels.
mic Use for headworn or lavalier microphones (PG1 only).
CHANNEL
D"
channel
ready
audio
Internal Diver
ENGLISH
Changing Channels
Press and hold the channel
button until the display starts
flashing.
Internal Anten
channel
ready
audio
While the display is flashing,
press the channel button.
The channel is active once
the display stops flashing.
channel
mute
channel
ready
audio
Internal Antenna Diversity
channel
mute
Receiver and transmitter
channels should match.
Multiple gain settings are available on the PG1 and PG2 transmitters.
To change gain settings, see below.
Follow these simple steps to check for interference and to
set your receiver and transmitter to the same channel
set your receiver and transmitter to the same channel
.
If you haven’t installed the
battery, do it now and leave the
cover off.
Turn
ON the handheld or
bodypack transmitter by
pressing the power button.
The channel display should
illuminate.
The ready LED on the receiver
should be illuminated.
Replace battery cover.
Check to see that the
transmitter and the receiver
display the same channel .
channel
ready
audio
Internal Diversity Antenna Syste
channel
mute
Internal Anten
channel
ready
audio
©2006, Shure Incorporated
27EN8865 (Rev. 3)
Printed in U.S.A.
The audio LED on the
receiver should flicker green
or amber, if red, adjust the
Gain Switch .
If this occurs, change the
channel.
Lock system controls to prevent accidental muting.
To lock controls: Turn transmitter off. Remove Battery Cover. Press
and hold Channel Button. Press and release Power/Mute button.
Power/Mute LED will flash red and green.
To unlock controls: Press and hold Power/Mute button down until
To unlock controls: Press and hold Power/Mute button down until
Power/Mute LED flashes red and green.
Locking and Unlocking Transmitter Controls
It turns off after ten seconds to
conserve battery.
Wearing the Bodypack Transmitter
Clip the transmitter to belt or
guitar strap as shown.
Make sure the antenna is
unobstructed.
Changing Battery
Expected life for a 9 volt alkaline battery is approximately 8 hours.When the
Power/Mute LED glows red, the battery should be replaced immediately.
System Components
audio
ready
channel
Diversity Antenna System
PG4
audio
ready
channel
audio
ready
channel
PG1
Bodypack
Transmitter
PG2 Handheld
Transmitter
PG4 Wireless
Receiver
PG88 Dual Wireless Receiver
PS20
Power Supply
PG185
Lavalier Mic
Features
PG30
Headworn Mic
Turn
OFF the microphone
or bodypack.
If left on, it will create a false
busy indicator.
Plug in the power supply.
There is no power switch.
The channel display should
illuminate.
If you see the
Busy
Indicator (a flashing dash)
change the channel.
Press and hold down the
channel button until the
display begins flashing.
Wait for the channel display
to stop flashing.