Latent Wireless. SC100 사용자 설명서
Wireless Adapter Quick Installation Guide
6.Specifications
7.FCC warning language
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Software Specification
Standard
IEEE802.11a,
IEEE 802.11n, IEEE 802.11g, IEEE 802.11b
Chipset
Ralink RT5572N
Wireless Speed
Frequency Range
Modulation Type
Antenna
Built-in PCB board antenna 2
dBi external antenna 2dBi
Work Mode
Ad-Hoc
Infrastructure
DSSS
Direct sequence spread spectrum
Wireless Security
64/128 bits WEP
WPA/WPA2, WPA -PSK/WPA2 -PSK (TKIP/AES)
Support Operating System
Windows 2000/XP/Vista/Linux/ Win 7/8/Mac
11b：CCK,DQPSK,DBPSK
11g：OFDM
11n：OFD
11g：OFDM
11n：OFD
ith PSK,BPSK,16-QAM,64-QAM
M W
2.4
02-2
.48
0GHz , 5180-5240MHz，5745-5825MHz
11n：up to 300Mbps
11g：6/9/12/18/24/36/48/54Mbps(adaptive)
11b：1/2/5.5/11M(adaptive)
11g：6/9/12/18/24/36/48/54Mbps(adaptive)
11b：1/2/5.5/11M(adaptive)
11a : up to 300Mbps
11a : OFDM
5. 5G wireless connection installation steps
Setup steps for 5G wireless connection is same as 2.4G mode.
All you need is to choose a 5G wireless access point.
All you need is to choose a 5G wireless access point.