ZHICHENG LIMITED 02 사용자 설명서
Following items are included
1
2
3
4
6
7
8
10
1. Volume -
2. Volume +
3. Noise reduction mic
4. Multifunction button
5. Status indicator
6. Trackback
7. Trackforward
8. Talking mic
9. Micro USB port
10. 3.5mm audio input jack
2. Volume +
3. Noise reduction mic
4. Multifunction button
5. Status indicator
6. Trackback
7. Trackforward
8. Talking mic
9. Micro USB port
10. 3.5mm audio input jack
Start here
Pair one phone
Basic operation
Call
Answer a call
Press the multifunction button.
End a call
Press the multifunction button.
Reject a call
Press and hold the volume button "+" for about 2 seconds.
Redial the last call
Double-press the multifunction button in standby mode. The
mobile phone will redial the last call number.
mobile phone will redial the last call number.
Mute on/off
Press the volume button "-" for about 2 seconds to mute
on/off.
on/off.
Pairing
3. Select "Headblue2" . If you phone asks, enter 0000 (four zeros)
for the passcode or accept the connection. The LED indicator
stops flashing red and blue once successfully paired.
Bluetooth
ON
Search
Bluetooth
ON
Connect
Headblue2
Pair another phone
Bluetooth ON
Connect
Headblue2
Bluetooth ON
Connect
Headblue2
5
9
1. Press and hold the Multifunction button for about 5 seconds, the
LED indicator flashes red and blue alternately.
2. Activate Bluetooth on your phone and set it to search for new
devices.
3. Select "Headblue2". If you phone asks, enter 0000 (four zeros) for
the passcode or accept the connection. The LED indicator stops
flashing red and blue once successfully paired.
4. Restart "Headblue2", it connects to two paired phone
automatically.
1. Press and hold the Multifunction button for about 5 seconds, the
LED indicator flashes red and blue alternately.
2. Activate Bluetooth on your phone and set it to search for new
devices.
NFC pairing
1. Press the multifunction button for about 2 seconds to turn on
the headphone.
2. Hold an NFC device against the NFC zone of the headphone
(right earcup). The LED indicator flashes red and blue, you hear
voice prompts "Pairing", the LED indicator stops flashing red
and blue once successfully paired, you hear voice prompts
"connection successful".
NFC detection area
Volume adjust
Press the "+" or "-" button to turn volume up or down, you hear
beep voice prompts once reach the maximum or minimum.
LED indicator and voice prompts
Instruction
Power on
Power off
Pairing
Standby
Incoming call
Battery low
LED status
Flashes blue 3 times
Flashes red 3 times
Flashes red and blue alternately
Flashes blue twice every 5 seconds
Flashes blue continuously
Flashes red twice every 2 seconds
Voice prompts
Power on
Power off
Pairing
/
/
Battery low
Multipoint technology enables you to pair another phone and
take a call from either.
Charging
Flashes red while charging
Flashes blue once fully charged
/
Music
(Need media player support)
Switch between the headphone and phone
Press the "+" button for about 2 seconds during a call, the call
will be switched to the mobile phone, redo this operation
again, the call will be switched to the headphone.
will be switched to the mobile phone, redo this operation
again, the call will be switched to the headphone.
Battery Indicator
Listen music via 3.5mm Jack
More features
Charging
Power off
Your new headphone has enough power to pair and make a few
calls.
When battery is low, you will hear the voice prompt " battery low ".
When battery is low, you will hear the voice prompt " battery low ".
It takes 2.5 hours to fully charge the headphone. While charging,
the battery indicator light is red, the indicator light flashes blue
once charging is complete.
Press and hold the Multifunction button for about 3 seconds. The
red LED will flash three times rapidly before turning off. A voice
prompt "power off" will appear, indicating the headphone has
been turned off.
Headblue 2
INSTRUCTION
1. Connect the headphone to a 3.5 mm jack connector on your
mobile device or PC using the supplied music cable.
2. Turn on the music player on your mobile device or computer,
you enjoy music from your headphone.
When the headphone is connected to a device with iOS system, a
battery indicator will appear at the upper right of the system,
indicating battery status of the headphone.
Note: The lifetime of the battery will be significantly reduced if your headphone
is left uncharged for a long period. We recommend that you recharge your
headphone at least once a month.
Music play / pause
Press multifunction button to play / pause music. (Some
phones may require you to start a media player first)
phones may require you to start a media player first)
Track back/forward
Press Track back to skip track backward, press Track
forward to skip track forward.
forward to skip track forward.
Switch Music and Call
When a call rings during a music playing, the music
automatically pauses to allow you to answer or ignore the
call. Once the call is ignored or ends, the music is resumed.
automatically pauses to allow you to answer or ignore the
call. Once the call is ignored or ends, the music is resumed.
Note: Call functions are disabled in this mode.
Hardware reset
Press and hold the multifunction button, connect the headphone
to a USB charger or USB port of computer, the LED indicator
flashes red, hardware reset is done in about 3 seconds.
3.5mm audio jack
USB cable
Product overview
Bluetooth headset
FCC ID:2AAIH02
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.