Invenco Group Ltd G6OPT 사용자 설명서
DCV-00001 Rev 05 S2 G6 OPT Installation Guide
Page 6
2.8 Safety Symbols and Warning Words
This section provides important information about warning symbols and boxes.
Alert Symbol: This safety alert symbol is used in this manual to alert you to a precaution
which must be followed to prevent potential personal safety hazards. Obey
safety directives that follow this symbol to avoid possible injury or death.
safety directives that follow this symbol to avoid possible injury or death.
Signal Words: These signal words used in this manual and on warning labels tell you the
seriousness of particular safety hazards. The precautions that follow must be followed to
prevent death, injury or damage to the equipment:
•
seriousness of particular safety hazards. The precautions that follow must be followed to
prevent death, injury or damage to the equipment:
•
WARNING - This alerts you to a hazard or unsafe practice that could result in death
or serious injury.
or serious injury.
•
CAUTION with Alert symbol - This signal word designates a hazard or unsafe
practice which may result in minor injury.
practice which may result in minor injury.
•
CAUTION without Alert symbol - When used by itself, CAUTION designates a hazard
or unsafe practice which may result in property or equipment damage.
or unsafe practice which may result in property or equipment damage.
2.9 Prevent Explosions and Fires
Fuels and their vapours will become explosive if ignited. Spilled or leaking fuels cause
vapours. Even filling customer tanks will cause explosive vapours in the vicinity of dispenser
or island.
vapours. Even filling customer tanks will cause explosive vapours in the vicinity of dispenser
or island.
2.10
No Open Flames
Open flames from matches, lighters, welding torches or other sources can ignite fuels and
their vapours.
their vapours.
2.11
No Sparks - No Smoking
Sparks from starting vehicles, starting or using power tools, burning cigarettes, cigars or pipes
can also ignite fuels and their vapours. Static electricity, including an electrostatic charge on
your body, can cause a spark sufficient to ignite fuels and their vapours. After getting out of a
vehicle, touch the metal of your vehicle to discharge any electrostatic charge before you
approach the dispenser island.
your body, can cause a spark sufficient to ignite fuels and their vapours. After getting out of a
vehicle, touch the metal of your vehicle to discharge any electrostatic charge before you
approach the dispenser island.
2.12
Working Alone
It is highly recommended that someone who is capable of rendering first aid be present during
servicing. Be familiar with Cardiopulmonary Resuscitation (CPR) methods if you are working
with or around high voltages. This information is available from the Red Cross. Always advise
the station personnel about where you will be working, and caution them not to activate power
while you are working on the equipment. Use the OSH tag out and lock out procedures. If you
are not familiar with this requirement, refer to information in the service manual and OSHA
documentation.
servicing. Be familiar with Cardiopulmonary Resuscitation (CPR) methods if you are working
with or around high voltages. This information is available from the Red Cross. Always advise
the station personnel about where you will be working, and caution them not to activate power
while you are working on the equipment. Use the OSH tag out and lock out procedures. If you
are not familiar with this requirement, refer to information in the service manual and OSHA
documentation.
2.13
Working With Electricity Safely
Be sure to use safe and established practices in working with electrical devices. Poorly wired
devices may cause a fire, explosion or electrical shock. Be sure grounding connections are
properly made. Make sure that sealing devices and compounds are in place. Be sure not to
pinch wires when replacing covers. Follow OSHA Lock-Out and Tag-Out requirements.
Station employees and service contractors need to understand and comply with this program
completely to ensure safety while the equipment is down.
devices may cause a fire, explosion or electrical shock. Be sure grounding connections are
properly made. Make sure that sealing devices and compounds are in place. Be sure not to
pinch wires when replacing covers. Follow OSHA Lock-Out and Tag-Out requirements.
Station employees and service contractors need to understand and comply with this program
completely to ensure safety while the equipment is down.
!