UHS Pty Ltd UM-ZW 사용자 설명서
UM-ZW Installer Manual RevC.docx
Page 3
3. Select Z-Wave Add\Remove in the drop
down menu.
4. Click Add.
5. Initiate LINK or ADD mode on Z-Wave
device. See your Z-Wave device’s manual
for instructions.
for instructions.
6. Note: If a Z-Wave device has been added
before or to another system, you must first
remove it before adding it to this system.
To do this, click Remove, then activate
LINK or REMOVE mode on the device.
remove it before adding it to this system.
To do this, click Remove, then activate
LINK or REMOVE mode on the device.
7. Click Rooms.
8. Check you can see the device you just
added. Click a button such as ON or OFF
to verify you can control the device.
to verify you can control the device.
Automation Scenes
Once Z-Wave devices have been added, they
can be switched on and off in response to
system events. Refer to the xGen Installation
& Programming Guide for instructions on
creating automation scenes.
can be switched on and off in response to
system events. Refer to the xGen Installation
& Programming Guide for instructions on
creating automation scenes.
Supported Z-Wave Devices
Type
Description
Binary On/Off
Switch
Switch
Non-secure mode, for controlling appliances
such as lamps, TV, garage door opener, and
other devices that connect to a power point.
such as lamps, TV, garage door opener, and
other devices that connect to a power point.
Dimmer
Non-secure mode, for controlling brightness
level of dimmable lights.
level of dimmable lights.
Door Locks
Secure mode only, supports locking,
unlocking, PIN code share, and status.
unlocking, PIN code share, and status.
Thermostat
Non-secure mode, control temperature set
points, on, off, fan, mode, and temperature
reading.
points, on, off, fan, mode, and temperature
reading.
Note on Range
Z-Wave devices form a wireless mesh network
where each device acts as a short-range
repeater.
Battery powered devices are not recommended
for use as repeaters due to limited battery life.
To extend the range of your Z-Wave network,
install mains powered Z-Wave devices such as
an On/Off power point.
For example, when adding a door lock, ensure
there is at least one mains powered Z-Wave
device between the lock and the UM-ZW Z-
Wave Module to provide more reliable
wireless coverage.
where each device acts as a short-range
repeater.
Battery powered devices are not recommended
for use as repeaters due to limited battery life.
To extend the range of your Z-Wave network,
install mains powered Z-Wave devices such as
an On/Off power point.
For example, when adding a door lock, ensure
there is at least one mains powered Z-Wave
device between the lock and the UM-ZW Z-
Wave Module to provide more reliable
wireless coverage.
Specifications
• Compatibility: xGen control panels
• Frequency: 908.42 MHz in US, 868.42
• Frequency: 908.42 MHz in US, 868.42
MHz in EMEA, 921.42 MHz in ANZ
• Required Power: 12.0 VDC (provided by
panel)
• Current Draw: 80 mA maximum
• Operating Temperature Range 0° to 49°C
• Operating Temperature Range 0° to 49°C
(32° to 120°F)
• Storage Temperature: -34° to 60°C (-30° to
120°F)
• Maximum Humidity: 90% relative
humidity non-condensing
• Dimensions: 155 mm H x 95 mm W x 68
mm D
Manufacturer
Placed on the market by:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.