Professional Security Corporation DBA Personal Safety Corporation WAM-1 사용자 설명서
battery signal to the WAM-1 monitor. WAM-1 monitor
blue LED light will flash periodically confirming the
transmitter low battery signal.
Sensor Pad Cleaning Instructions
Use the same cleaning method used to clean vinyl mattress
covers. A damp, non-abrasive cloth may be used to wipe
sensor pads and floor mat. All cleaning products suitable for
vinyl may be used to wipe bed/chair sensor pads.
Water and Incontinent Proof
The Wireless Sensor pads have been specially designed
to be water and incontinent proof. If sensor is exposed to
extreme heat, punctured or torn it will no longer be water and
incontinent proof and should no longer be used under any
circumstance.
Warning: Do not immerse sensor pads in water for any
reason. Doing so will void warranty.
Warning: Do not immerse sensor pads in water for any
reason. Doing so will void warranty.
Troubleshooting
1. Install new batteries in both the WAM-1 and WAT-1. If
using optional WAM-1 AC power adapter, verify that it is
properly plugged in to both the WAM-1 and the wall.
2. Make sure WAM-1 and WAT-1 are properly SYNCED.
(See Step 3 of Setup Instructions)
3. Determine WAT-1 is working:
a. Confirm that the ON/OFF switch is in the ON position.
b. Confirm that the sensor pad or floor mat is plugged into
the WAT-1
c. To Press or release the PAD, it can initial the LED on
WAT-1 to turn on periodically.
4. Determine WAM-1 is working:
a. Hold the “Reset” button on the front of the WAM-1 for a
few seconds; all LED lights will turn on and it will emit a
tone sound.
5. Determine which component is at fault:
a. Use a known working WAT-1/WAM-1 set and connect
the potentially faulty sensor pad to test functionality.
If the set does not function properly, the sensor pad is
faulty and should be replaced.
b. Take a known working sensor pad and connect the
potentially faulty WAT-1/WAM-1 – if the system does not
function properly, the WAT-1 or WAM-1 are faulty and
should be replaced
Technical Specifications
Wireless Alarm Monitor (WAM-1)
Power: 3x AA Alkaline Batteries (included) and DC6V 1A
(optional AC adapter)
Wireless Operating Frequency: 2.4G
Wireless Technology: GFSK RF module
Visual Alert: Monitor low bat. LED, WAT-1 low bat. LED,
Wireless Technology: GFSK RF module
Visual Alert: Monitor low bat. LED, WAT-1 low bat. LED,
alarm LED and sync LED indication
Audible Alarm: Tone and dB level adjustability
Housing: Gray ABS plastic
Dimensions: 135mm x 85mm x 41mm; 138mm x 91mm
Housing: Gray ABS plastic
Dimensions: 135mm x 85mm x 41mm; 138mm x 91mm
x 46mm (with plastic holder)
Wireless Alarm Transmitter (WAT-1)
Power: 2x AAA Alkaline Batteries (included)
Wireless Operating Frequency: 2.4G
Wireless Technology: GFSK RF module
Visual Indicator: WAT-1 low bat LED and transmit LED
Wireless Operating Frequency: 2.4G
Wireless Technology: GFSK RF module
Visual Indicator: WAT-1 low bat LED and transmit LED
indication
Housing: Gray ABS plastic
Dimensions: 70mm x 70mm x 15mm
Dimensions: 70mm x 70mm x 15mm
12 Month Limited Warranty
Personal Safety Corporation warrants this product to be
free from factory defects in materials and workmanship for
a period of 12 months from the date on the product. Void if
this product is misused, abused or punctured. No warranty or
responsibility of use expressed or implied.
IMPORTANT: The Secure Wireless Patient Monitoring
System operates using wireless RF technology which is
subject to physical and environmental considerations. The
system must always be tested by the end user before each
use in the setting in which they are to be used. It is important
to consider that the operating distance of the monitor
and transmitter is limited depending on the environment
factors such as walls, appliances, etc. Both the monitor and
transmitter are battery operated and the life of the batteries
may vary based on usage.
TM
PATIENT
MONITORING SYSTEM
Continued
Please see our complete line of Secure
®
fall & wandering prevention products at www.PadAlarm.com.
Highest Quality...Lowest Prices...Guaranteed!
Personal Safety Corporation • Hiawatha, Iowa 52233 • 800.373.2873
01/21/15
CAUTION!
This product is designed as a monitor, alerting the staff when a patient has risen from their bed or chair. This
product is not a retraint and therefore will not prevent a patient from getting out of their bed or chair. This
product is to be used in conjunction with a total fall prevention program.
DO NOT ASSUME!
This product must be tested each time it is used with a patient to make sure it functions properly.