JVC TH-R3: DVD Recordable Digital Cinema System TH-R3 사용자 설명서
제품 코드
TH-R3
Filename [TH-R1R3EU_05Name.fm]
Masterpage:Left0
Page 11Monday, 28 March 2005 21:23
11
INSTALLING YOUR NEW UNIT
It’s essential that your unit be properly connected.
1
Make sure the package contains all of the accessories listed in
AACCESSORIESB (A pg. 92).
AACCESSORIESB (A pg. 92).
2
Place the unit on a stable, horizontal surface.
3
Connect the unit to a TV depending on the TV and cables you
use.
use.
8 Basic Connection
To connect to a TV with 21-pin SCART input connector ^
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the [TV ANTENNA IN] connector
To connect to a TV with 21-pin SCART input connector ^
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the [TV ANTENNA IN] connector
on the rear panel of the unit.
C Connect the [TV ANTENNA OUT] connector on the rear panel
of the unit and the TV’s aerial connector with the supplied RF
cable.
cable.
D Connect the [L-1 INPUT/OUTPUT] connector on the rear panel
of the unit and the TV’s 21-pin SCART connector with a
supplied 21-pin SCART cable.
supplied 21-pin SCART cable.
●
The [L-1 INPUT/OUTPUT] connector accepts and delivers
either a composite signal (regular video signal), Y/C signal or
RGB signal.
either a composite signal (regular video signal), Y/C signal or
RGB signal.
●
Set your TV to the VIDEO, Y/C, or RGB mode according to the
type of your TV’s SCART connector.
type of your TV’s SCART connector.
8 Component Video Connection
To connect to TV’s component video input connectors ^
A Perform steps A - C of ABasic ConnectionB.
To connect to TV’s component video input connectors ^
A Perform steps A - C of ABasic ConnectionB.
B Connect the unit’s [COMPONENT VIDEO OUT (Y/P
B
/P
R
)]
connectors to the TV’s component video input connectors.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
●
You can obtain high-quality component video pictures.
●
By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to
images in the progressive mode. For switching to the
progressive mode, refer to
●
Select an appropriate option of
AL-1 OUTPUTB as follows
When the setting selected is not in accordance with the TV
connected and depending on the type of appliance connected to
the unit, the correct picture will not appear.
connected and depending on the type of appliance connected to
the unit, the correct picture will not appear.
●
If you possess a satellite receiver, refer to
B as well. (A pg. 71)
●
Connecting the FM and AM antennas (A pg. 12)
●
Connecting the satellite speakers (A pg. 14)
●
Connecting the powered subwoofer (A pg. 16)
●
Connecting the power cord (A pg. 16)
Connecting The TV And TV Antenna
●
Your TV must have a 21-pin AV input connector (SCART) for
the basic connection to the unit.
the basic connection to the unit.
●
Connect the AC plug only after all connections to the TV has
been completed.
been completed.
IN
OUT
RIGHT
LEFT
TV aerial cable
Mains outlet
Back of unit
Component
video cable
(not supplied)
video cable
(not supplied)
TV
Mains power
cord
Audio
cable
(not
supplied)
cable
(not
supplied)
To
[COMPONENT
VIDEO OUT
(Y/P
[COMPONENT
VIDEO OUT
(Y/P
B
/P
R
)]
RF cable
(supplied)
(supplied)
21-pin SCART
cable
(supplied)
cable
(supplied)
To 75 ohm terminal
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
OPERATION CAN BE PERFORMED.
When your TV’s SCART
connector accepts:
connector accepts:
Set
AL-1 OUTPUTB to:
Composite signals
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
luminance (brightness) and
chrominance (colour) signals)
RGB signal
Component video signal
TH-R1R3EU_00.book Page 11 Monday, March 28, 2005 9:23 PM