Intel III Xeon 700 MHz 80526KY7002M 사용자 설명서
제품 코드
80526KY7002M
PROCESSOR FEATURES
50
uniquely determined for each unit. The procedure causes each unit to dissipate its maximum power (which
can vary from unit to unit) while at the same time maintaining the thermal plate at its maximum specified
operating temperature. Correctly used, this feature permits an efficient thermal solution while preserving data
integrity.
The thermal byte reading can be used in conjunction with the Thermal Reference Byte in the processor
Information ROM. Byte 9 of the processor Information ROM contains the address in the ROM of this byte,
described in more detail in Section 5.2.5. The thermal byte reading from the thermal sensor can be compared
to this Thermal Reference Byte, to provide an indication of the difference between the temperature of the
processor core at the instant of the thermal byte reading and the temperature of the processor core under the
steady state conditions of high power and maximum TPLATE specifications. The nominal precision of the
least significant bit of a thermal byte is 1°C.
Reading the thermal sensor is explained in Section 5.2.6.
The thermal sensor feature in the processor cannot be used to measure TPLATE. The TPLATE specification
in Chapter 6 must be met regardless of the reading of the processor's thermal sensor in order to ensure
adequate cooling for the entire processor. The thermal sensor feature is only available while VCC_CORE and
VCC_SMB are at valid levels and the processor is not in a low-power state.
can vary from unit to unit) while at the same time maintaining the thermal plate at its maximum specified
operating temperature. Correctly used, this feature permits an efficient thermal solution while preserving data
integrity.
The thermal byte reading can be used in conjunction with the Thermal Reference Byte in the processor
Information ROM. Byte 9 of the processor Information ROM contains the address in the ROM of this byte,
described in more detail in Section 5.2.5. The thermal byte reading from the thermal sensor can be compared
to this Thermal Reference Byte, to provide an indication of the difference between the temperature of the
processor core at the instant of the thermal byte reading and the temperature of the processor core under the
steady state conditions of high power and maximum TPLATE specifications. The nominal precision of the
least significant bit of a thermal byte is 1°C.
Reading the thermal sensor is explained in Section 5.2.6.
The thermal sensor feature in the processor cannot be used to measure TPLATE. The TPLATE specification
in Chapter 6 must be met regardless of the reading of the processor's thermal sensor in order to ensure
adequate cooling for the entire processor. The thermal sensor feature is only available while VCC_CORE and
VCC_SMB are at valid levels and the processor is not in a low-power state.
5.2.5
THERMAL SENSOR SUPPORTED SMBUS TRANSACTIONS
The thermal sensor responds to five of the SMBus packet types: write byte, read byte, send byte, receive
byte, and ARA (Alert Response Address). The send byte packet is used for sending one-shot commands only.
The receive byte packet accesses the register commanded by the last read byte packet. If a receive byte
packet was preceded by a write byte or send byte packet more recently than a read byte packet, then the
behavior is undefined. Tables 36 through 40 diagram the five packet types. In these figures, ‘S’ represents the
SMBus start bit, ‘P’ represents a stop bit, ‘Ack’ represents an acknowledge, and ‘///’ represents a negative
acknowledge. The thermal sensor transmits the shaded bits and the SMBus host controller transmits the bits
that aren’t shaded. Table 41 shows the encoding of the command byte.
byte, and ARA (Alert Response Address). The send byte packet is used for sending one-shot commands only.
The receive byte packet accesses the register commanded by the last read byte packet. If a receive byte
packet was preceded by a write byte or send byte packet more recently than a read byte packet, then the
behavior is undefined. Tables 36 through 40 diagram the five packet types. In these figures, ‘S’ represents the
SMBus start bit, ‘P’ represents a stop bit, ‘Ack’ represents an acknowledge, and ‘///’ represents a negative
acknowledge. The thermal sensor transmits the shaded bits and the SMBus host controller transmits the bits
that aren’t shaded. Table 41 shows the encoding of the command byte.
Table 36. Write Byte SMBus Packet
S Address Write Ack
Command
Ack
Data
Ack
P
1 7
bits
1 1
8 bits
1
8 bits
1
1
Table 37. Read Byte SMBus Packet
S Address Write Ack
Command
Ack
S Address Read Ack
Data
/// P
1 7
bits 1 1
8 bits
1
1
7 bits
1
1
8 bits
1 1
Table 38. Send Byte SMBus Packet
S Address Write
Ack
Command
Ack
P
1 7
bits
1
1
8 bits
1
1
Table 39. Receive Byte SMBus Packet
S Address Read Ack
Data
/// P
1 7
bits
1
1
8 bits
1 1
Table 40. ARA SMBus Packet
S ARA Read Ack
Address
/// P
1 0001
100
1
1
Device Address
1
1 1
NOTE: