Valcom V-1036M 전단
15-WATT AMPLIFIED HORNS
MODEL
V-1036C,
V-1036M
Valcom, Inc. 5614 Hollins Road Roanoke, Virginia 24019 Phone: 540-563-2000 Fax: 540-362-9800
E-Mail: info@valcom.com www.valcom.com
Page
2
Technical Specification
ARCHITECTS’ AND ENGINEERS
The 15-Watt Amplified Horn, Model V-1036C, shall be an FCC registered, weather-resistant, high efficiency
reentrant type horn with high frequency diffuser. It shall be equipped with an amplifier, externally accessible
volume control. It shall include a detachable base for wall or single, double or octagon electrical box mounting
and omni-directional ball joint mounting bracket to allow precise positioning in the vertical and horizontal planes
with a single adjustment. An I-beam mounting clamp shall also be provided. The FCC registration number shall
be BAFUSA-69358-KX-N.
The frequency response shall by 225 Hz to 14 kHz. Dispersion shall be 120 horizontal and 90° vertical. Sound
pressure level shall be 121 dB measured at 4 feet (1.22 m) on axis with an input to the amplifier module being -
10 dBm at 1 kHz. Distortion shall be less than 2.0% at rated output of 15 watts RMS. Output load shall be 8
ohms. Input impedance shall be 600 ohms nominal. The amplifier shall operate on a -24 Vdc nominal, positive
ground power supply. Operating current shall be 900 mA at -24 Vdc. Operating temperature shall be -4 to 131
°F (-20 to 55 °C). Operating humidity shall be 0-95% noncondensing.
The horn shall be constructed of high impact ABS plastic. The mounting base shall be constructed of LEXAN®
an ultra-high impact material which is stronger and tougher than die casting. The finish shall be beige with
brown accent. The I-beam mounting clamp shall be constructed of zinc chromate plated steel.
Dimensions of the horn shall be 7.38 "H x 10.0 "W x 10.4 "D (18.7452 cm x 25.4 cm x 26.416 cm). Weight shall
be approximately
reentrant type horn with high frequency diffuser. It shall be equipped with an amplifier, externally accessible
volume control. It shall include a detachable base for wall or single, double or octagon electrical box mounting
and omni-directional ball joint mounting bracket to allow precise positioning in the vertical and horizontal planes
with a single adjustment. An I-beam mounting clamp shall also be provided. The FCC registration number shall
be BAFUSA-69358-KX-N.
The frequency response shall by 225 Hz to 14 kHz. Dispersion shall be 120 horizontal and 90° vertical. Sound
pressure level shall be 121 dB measured at 4 feet (1.22 m) on axis with an input to the amplifier module being -
10 dBm at 1 kHz. Distortion shall be less than 2.0% at rated output of 15 watts RMS. Output load shall be 8
ohms. Input impedance shall be 600 ohms nominal. The amplifier shall operate on a -24 Vdc nominal, positive
ground power supply. Operating current shall be 900 mA at -24 Vdc. Operating temperature shall be -4 to 131
°F (-20 to 55 °C). Operating humidity shall be 0-95% noncondensing.
The horn shall be constructed of high impact ABS plastic. The mounting base shall be constructed of LEXAN®
an ultra-high impact material which is stronger and tougher than die casting. The finish shall be beige with
brown accent. The I-beam mounting clamp shall be constructed of zinc chromate plated steel.
Dimensions of the horn shall be 7.38 "H x 10.0 "W x 10.4 "D (18.7452 cm x 25.4 cm x 26.416 cm). Weight shall
be approximately
3.7 lbs (1.665 kg)
.
LEXAN
® Registered Trademark of General Electric Co.
Limited Warranty
Valcom, Inc. warrants its products to be free from defects in materials and workmanship under conditions of
nor-mal use and service for a period of one year from the date of shipment. The obligation under this warranty
shall be limited to the re-placement, repair or refund of any such defective device within the warranty period,
provided that:
nor-mal use and service for a period of one year from the date of shipment. The obligation under this warranty
shall be limited to the re-placement, repair or refund of any such defective device within the warranty period,
provided that:
1. inspection by Valcom, Inc. indicates the validity of the claim,
2. the defect is not the result of damage, misuse, or negligence after the original shipment,
3. the product has not been in any way repaired by others and that factory sealed units are unopened (A
2. the defect is not the result of damage, misuse, or negligence after the original shipment,
3. the product has not been in any way repaired by others and that factory sealed units are unopened (A
service charge plus parts and labor will be applied to units defaced or physically damaged).
4. freight charges for the return of products to Valcom, Inc. are prepaid,
5. all units “out of warranty” are subject to a service charge. The service charge will cover minor repairs
5. all units “out of warranty” are subject to a service charge. The service charge will cover minor repairs
(major repairs will be subject to additional charges for parts and labor)
This warranty is in lieu of and excludes all other warranties expressed or implied, and in no event shall Valcom, Inc.
be liable for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in
connection with the purchase, operation or use of the product.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition,
the carrier should be notified immediately. Claims for such damage should be filed with the carrier involved in accordance
with the F.O.B. point.
be liable for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in
connection with the purchase, operation or use of the product.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition,
the carrier should be notified immediately. Claims for such damage should be filed with the carrier involved in accordance
with the F.O.B. point.