Troy-Bilt CSV206 사용자 설명서

8

•

Read, understand, and follow all instructions and 
warnings on the machine and in this manual before 
operating. A pair of safety glasses has been 
provided with this equipment.

Service the engine with gasoline and oil as instructed in 
the engine manual. Read instructions carefully.

•

Attach spark plug wire to spark plug. Make certain 
the metal cap on the end of the spark plug is 
fastened securely over metal tip on the spark plug.

•

Make certain drive clutch control is in the 
disengaged (released) position.

•

Engines with choke lever: Move choke lever on 
engine to CHOKE position. (A warm engine may 
not require choking).

•

Engines with primer: Prime engine as instructed 
in the engine manual.

•

Move engine throttle control lever to FAST or 
START position.

•

Place one foot on the left rear wheel to prevent the 
unit from skidding while starting.

•

Grasp starter handle and pull rope out slowly until 
engine reaches start of compression cycle (rope 
will pull slightly harder at this point).

NOTE:  A noise will be heard at the start of the
compression cycle, which will continue to be heard till
the impeller reaches full speed.   

•

Keeping a firm grip on the starter handle, pull rope 
with a rapid, continuous, full arm stroke. Let the 
rope rewind slowly.

•

Repeat until engine cranks. When engine starts, 
move choke control (if equipped) gradually to RUN 
position.

•

Open the large zipper in the rear of the bag to 
empty the contents. Be certain the zipper is closed 
completely when operating the unit.

•

If bag is removed for any reason, follow instructions 
for attaching the bag in the ASSEMBLY section. 

•

To engage the wheel drive, hold the drive clutch 
control against the upper handle. 

•

Release the drive clutch control to stop the rear 
wheels from driving. 

•

Release the drive clutch control to slow down when 
negotiating an obstacle, making a turn, or stopping. 

•

Engage control slowly to prevent the front wheels 
from lifting up.

•

Place both hands on top of upper handle to push 
unit over yard waste. Yard waste such as leaves 
and pine needles can be vacuumed up through the 
nozzle for shredding. 

•

After material has been shredded by the blades on 
the impeller assembly, it will be discharged into 
catcher bag. Do not attempt to shred or chip any 
material other than vegetation found in a normal 
yard (i.e. branches, leaves, twigs, etc.) Avoid 
fibrous plants such as tomato vines until they are 
thoroughly dried out. Materials such as stalks or 
heavy branches up to 3” in diameter may be fed 
into the chipper chute. 

The flail screen is located inside the 

housing in the discharge area. If the flail screen 
becomes clogged, remove and clean as instructed in 
the maintenance section. For best performance, it is 
also important to keep the chipper blade sharp. 

(Pneumatic tires only)

Maximum tire pressure under any circumstance is 30 
psi. Equal tire pressure should be maintained at all 
times.

Always wear safety glasses 

during operation or while performing any 
adjustments or repairs. Thrown objects which 
ricochet can cause serious injury to the eyes. 

Use extreme care when 

handling gasoline. Gasoline is extremely 
flammable and the vapors are explosive. Never 
fuel machine indoors or while the engine is hot 
or running. Extinguish cigarettes, cigars, pipes, 
and other sources of ignition.

Keep bystanders, helpers, pets, 

and children at least 75 feet from the machine 
before starting and while operating. Do not 
operate this machine unless the discharge 
chute and bag have been properly installed 
and secured to the machine. 

Do not attempt to shred, chip, or 

vacuum any material larger than specified on 
the machine or in this manual. Personal injury 
or damage to the machine could result.