True Manufacturing Company TCGD-50 사용자 설명서
............ www.truemfg.com ............
True Food Service Equipment, Inc.
3
3
Before your new display case is connected to a
power supply, check the incoming voltage with a
voltmeter. If anything less than 100% of the rated
voltage for operation is noted, correct immediately.
power supply, check the incoming voltage with a
voltmeter. If anything less than 100% of the rated
voltage for operation is noted, correct immediately.
Have the circuit checked by a qualified electrician
to make sure it is properly grounded.
to make sure it is properly grounded.
The display case should always be use it’s own
individual electrical circuit, which has a voltage
rating that matches the rating plate.
individual electrical circuit, which has a voltage
rating that matches the rating plate.
This provides the best performance and also
prevents overloading building wiring circuits which
could cause a fire hazard from overheated wires.
prevents overloading building wiring circuits which
could cause a fire hazard from overheated wires.
For models with Optional 12" (30.5 cm) cord.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard
from this appliance.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard
from this appliance.
Have the circuit checked by a qualified electrician
to make sure it is properly grounded.
to make sure it is properly grounded.
If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it
replaced with the properly grounded 3-prong wall
outlet.
personal responsibility and obligation to have it
replaced with the properly grounded 3-prong wall
outlet.
The display case should always be plugged into
it’s own individual electrical circuit, which has a
voltage rating that matches the rating plate.
it’s own individual electrical circuit, which has a
voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading building wiring circuits which
could cause a fire hazard from overheated wires.
prevents overloading building wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your display case by pulling on
the power cord. Always grip plug firmly and pull
straight out from the outlet.
the power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When removing the display case away from the
wall, be careful not to roll over or damage the
power cord.
wall, be careful not to roll over or damage the
power cord.
HOW TO CONNECT ELECTRICITY
Hard wiring is required on standard "Dry" Display Cases.
Optional 12" (30.5 cm) corded model available, factory installed only
(exterior scale receptacle will not be included with this option).
Optional 12" (30.5 cm) corded model available, factory installed only
(exterior scale receptacle will not be included with this option).
WARNING!
NOTE
Applies to models ordered with 12" power
cord, hard wired models do not use this
receptacle.
Applies to models ordered with 12" power
cord, hard wired models do not use this
receptacle.
USE OF ADAPTER PLUGS
NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain conditions, we strongly
recommend against the use of an adapter plug.
recommend against the use of an adapter plug.
SAFETY INFORMATION
NEMA plugs
TRUE uses these types of plugs.
If you do not have the right outlet
have a certified electrician install
the correct power source.
115/60/1
NEMA-5-15R
NEMA-5-15R