JVC 0503-FO-ID-VP 사용자 설명서
EN
61
Master Page: Right
NOTES:
● When editing onto a tape that was recorded at
12-bit, the old and new soundtracks are recorded
separately.
separately.
● If you dub onto a blank space on the tape, the
sound may be disrupted. Make sure you only edit
recorded areas.
recorded areas.
● If feedback or howling occurs during TV playback,
move the camcorder’s microphone away from the
TV, or turn down the TV’s volume.
TV, or turn down the TV’s volume.
● If you change from 12-bit to 16-bit in mid-
recording and then use the tape for Audio
Dubbing, it is not effective from the point where
16-bit recording began.
Dubbing, it is not effective from the point where
16-bit recording began.
● During Audio Dubbing, when the tape moves to
scenes recorded in the LP mode, scenes recorded
in 16-bit audio or a blank portion, Audio Dubbing
stops.
in 16-bit audio or a blank portion, Audio Dubbing
stops.
● To perform Audio Dubbing while watching on the
television, make connections. (
墌 pg. 26)
● To perform Audio Dubbing with a video unit
connected to the camcorder’s S/AV connector, first
set “S/AV INPUT” to “A/V IN” or “S IN” in VIDEO
Menu. (
set “S/AV INPUT” to “A/V IN” or “S IN” in VIDEO
Menu. (
墌 pg. 35, 41)
The “AUX” indication appears instead of “MIC”.
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and outpoints. The original audio remains
unchanged.
A tape that was recorded in HD or SD mode cannot
be used for Insert Editing.
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and outpoints. The original audio remains
unchanged.
A tape that was recorded in HD or SD mode cannot
be used for Insert Editing.
NOTES:
● Before performing the following steps, make sure
that “TIME CODE” is set to “ON”. (
墌 pg. 35, 42)
● Insert Editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
● To perform Insert Editing while watching in the
television, make connections. (
墌 pg. 26)
1
Play back the tape, locate the Edit-Out point and
press PAUSE (9). Confirm the time code at this
point. (
press PAUSE (9). Confirm the time code at this
point. (
墌 pg. 42)
2
Press REW (3) until the Edit-In point is located,
then press PAUSE (9).
then press PAUSE (9).
3
Press and hold INSERT (I) on the remote
control, then press PAUSE (9). The “9I”
control, then press PAUSE (9). The “9I”
indicator and the Time Code (min.:sec.) appear
and the camcorder enters Insert-Pause mode.
and the camcorder enters Insert-Pause mode.
4
Press START/STOP to begin editing.
● Confirm the insert at the time code you
checked in step 1.
● To pause editing, press START/STOP. Press it
again to resume editing.
5
To end Insert Editing, press START/STOP, then
STOP (8).
STOP (8).
NOTES:
● During Insert Editing, set the Recording Mode
Switch to “DV”.
● Special Effects (墌 pg. 51) can be used to spice up
the scenes being edited during Insert Editing.
● During Insert Editing, the date and time
information changes.
● If you perform Insert Editing onto a blank space on
the tape, the audio and video may be disrupted.
Make sure you only edit recorded areas.
Make sure you only edit recorded areas.
● During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Editing stops. (
portion, Insert Editing stops. (
墌 pg. 76)
● If a memory card is loaded and “NAVIGATION” is
set to other than “MANUAL”, a NAVIGATION
thumbnail image is stored in the memory card.
(
thumbnail image is stored in the memory card.
(
墌 pg. 52)
Insert Editing (DV only)
PAUSE
START/STOP
INSERT
PLAY
PLAY
REW
STOP
AD
V
A
NCED FE
A
TURE
S
GR-HD1US_07Advanced.fm Page 61 Thursday, April 17, 2003 3:44 PM