JVC HR-J674EU 사용자 설명서
Filename [HRJ670EU2.fm]
Masterpage:Right
EN
27
F
Enter the channel position.
G
Set the tape speed.
(HR-J670/671/672/673/674/470/
472EU only)
(HR-J670/671/672/673/674/470/
472EU only)
Press SP/LP (
p
).
H
Set the VPS/PDC mode.
Press VPS/PDC to select “ON” or “OFF”.
● If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC”
is lit on the front display panel, VPS/PDC is set to ON.
● If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC”
is not lit on the front display panel, VPS/PDC is set to OFF.
墌
“VPS/PDC Recording” in the right column
I
Return to the normal screen.
After confirming all information is correct, press PROG or
OK. “PROGRAM COMPLETED” appears on the TV
screen for about 5 seconds, then the normal screen
appears. If “PROGRAM OVERLAPPED” appears on the
TV screen and “Err” on the front display panel, see
page 29.
OK. “PROGRAM COMPLETED” appears on the TV
screen for about 5 seconds, then the normal screen
appears. If “PROGRAM OVERLAPPED” appears on the
TV screen and “Err” on the front display panel, see
page 29.
● Repeat steps 1 – 9 for each additional programme.
J
Engage the recorder’s timer mode.
Press
#
(TIMER). The recorder turns off automatically
and
#
appears on the front display panel.
● To disengage the timer mode, press
#
(TIMER) again.
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps 2 through 9, press WEEKLY (NUMBER
key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the TV screen. Pressing the button again makes the
corresponding indication disappear.
key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the TV screen. Pressing the button again makes the
corresponding indication disappear.
NOTE:
You can programme this recorder to timer-record as many as 8
programmes. If you try to programme the recorder to record a
ninth, “PROGRAM FULL” appears on the TV screen and “FULL”
appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary programmes
(
programmes. If you try to programme the recorder to record a
ninth, “PROGRAM FULL” appears on the TV screen and “FULL”
appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary programmes
(
墌
pg. 28).
Press PR +/–.
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer
Programming:
Programming:
A Perform “Satellite Receiver Control Setting” on page 13.
B Perform steps 1 – 10. In step 6, press the NUMBER key
“0” to change “TV PROG” to “SAT”. The front display
panel shows “L-2” for the channel position. Then press PR
+/– to enter the channel position for the satellite
broadcast. In step 8, you cannot set “VPS/PDC” to “ON”.
panel shows “L-2” for the channel position. Then press PR
+/– to enter the channel position for the satellite
broadcast. In step 8, you cannot set “VPS/PDC” to “ON”.
C Leave the satellite receiver’s power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
● When you use Express Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
listing. A different time than advertised will result in no
recording.
● VPS/PDC recording is also possible when a satellite
receiver or a cable system is connected to AV2 (L-2) IN/
DECODER on your recorder.
DECODER on your recorder.
● VPS/PDC recording is also possible via the AV1 (L-1) IN/
OUT connector.
How to check if the station being received transmits a
VPS/PDC signal
VPS/PDC signal
A Press – –:– – until the channel position appears on the
front display panel.
B Hold down START+ for about 5 seconds.
“VPS/PDC” appears blinking on the front display panel.
If a VPS/PDC signal is detected from the station, “VPS/
PDC” will stop blinking.
If no VPS/PDC signal is detected from the station, “VPS/
PDC” will blink at a slower rate.
If a VPS/PDC signal is detected from the station, “VPS/
PDC” will stop blinking.
If no VPS/PDC signal is detected from the station, “VPS/
PDC” will blink at a slower rate.
C Press – –:– – or START+ again to return to normal display.
HRJ670EU2.fm Page 27 Wednesday, April 26, 2000 5:21 PM