JVC HR-VP655U 사용자 설명서
EN
37
1
2
3
4
5
6
7
8
9
0
2
4
1
3
PROG.
OK
TIMER
SP/EP
PROGRAM 1
(VCR PLUS+ 12345678)
START
STOP
8:00PM
= 10:00PM
DATE
CH
12/24/98
12 SP
THU
PRESS (8=DAILY, 9=WEEKLY
STOP+/– = STOP TIME, SP/EP)
PRESS (OK) TO END
STOP+/– = STOP TIME, SP/EP)
PRESS (OK) TO END
NUMBER "9"
NUMBER "8"
CANCEL
STOP+/–
CHECK PROGRAM DATA
5
The PlusCode number you
entered and the matching
Timer-Recording informa-
tion is displayed on the
Program screen. Check to
make sure it’s accurate.
entered and the matching
Timer-Recording informa-
tion is displayed on the
Program screen. Check to
make sure it’s accurate.
● To change the stop time,
press STOP +/–.
● To timer-record daily or weekly serials, press DAILY
(NUMBER “8”) or WEEKLY (NUMBER “9”). “DAILY”
or “WEEKLY” appears on the Program screen.
Pressing the button again makes each corresponding
display disappear.
or “WEEKLY” appears on the Program screen.
Pressing the button again makes each corresponding
display disappear.
● If you made a mistake, press CANCEL to access the
VCR Plus+ screen again and input the correct
PlusCode number.
PlusCode number.
● If the PlusCode number you inputted is incorrect,
"ERROR" may appear on the screen to advise you of
the error. This happens when the PlusCode number is
for a program which has already passed. "ERROR" is
displayed for about 5 seconds and the VCR Plus+
screen reappears.
the error. This happens when the PlusCode number is
for a program which has already passed. "ERROR" is
displayed for about 5 seconds and the VCR Plus+
screen reappears.
SET TAPE SPEED
6
Press SP/EP.
RETURN TO NORMAL
SCREEN
7
Press PROG. or OK. "PROGRAM COMPLETED"
appears on the screen for about 5 seconds, then normal
screen appears.
appears on the screen for about 5 seconds, then normal
screen appears.
ENGAGE TIMER MODE
8
Press TIMER. The VCR turns off automatically and "‰"
is displayed on the display panel.
is displayed on the display panel.
IMPORTANT
If you have moved to a different area or if a broadcasting
station's channel number has been changed, the wrong VCR
or CABLE CH number will be displayed on the VCR Plus+
Program screen in step 5. When this happens, set the correct
the Guide Channel number for that station. (
station's channel number has been changed, the wrong VCR
or CABLE CH number will be displayed on the VCR Plus+
Program screen in step 5. When this happens, set the correct
the Guide Channel number for that station. (
Z
pg. 38,
"VCR Plus+ Setup")
NOTES:
● To disengage the timer before recording starts, press TIMER
again. Pressing once more re-engages it.
● In case of a power failure after programming, the VCR’s
memory backup keeps your selections for approximately
10 minutes.
10 minutes.
● When timer-recording cable channels received through a
Cable Box, be sure to keep the Cable Box set to ON.
10:00
11:00
12:00
ATTENTION
If there is a conflict in the timer schedule and one program
overlaps with another, only the parts shown below in gray
will be recorded.
overlaps with another, only the parts shown below in gray
will be recorded.
Pattern 1: The program with the lower program number
will be recorded.
Pattern 2: The program that is broadcast earlier will be
recorded.
Pattern 3: The program that is broadcast earlier will be
recorded, followed by the remaining portion of
the other program.
the other program.
CH10
CH40
CH40
Not recorded
Program 1
Program 2
10:00
11:00
12:00
CH10
Program 2
Not recorded
Program 1
CH40
10:00
11:00
12:00
CH10
CH40
Program 1
Program 2
Not recorded