Alcatel-Lucent OS9-GNI-U24 사용자 설명서

다운로드
페이지 90
 
 
Alcatel-Lucent 
Page 34 
 
OmniSwitch 9000
 
 
 
 
  
 
 
 
 
OS9-GNI-P24 Technical Specifications Overview 
OS9-GNI-P24 Technical Specifications Overview 
Number of MiniGBIC ports 
24 x 1000BASE-T twisted Pair 
Connector types 
RJ-45 
Standards supported 
IEEE 802.3z; IEEE 802.3ab, 802.3af (DTE Power via MDI MIB); and 1000BASE-T 
Data rate 
10Mbps or 100Mbps (full or half duplex)  
1000Mbps (1 Gigabit per second) (full duplex) 
Maximum frame size 
1553 Bytes (on 10mbps or 100Mbps interfaces) 
9,216 bytes (on 1 Gigabit Ethernet interfaces) 
OS9-GNI-P24 modules support jumbo frames (1,500 to 9,216 bytes) 
MAC addresses supported 
There are now two source learning modes available for the OmniSwitch 9000 Series switches: synchronized 
and distributed. By default the switch runs in the synchronized mode, which allows a total MAC address tables 
size of 16K per chassis. Enabling the distributed mode for the switch increases the table size to 16K per module 
and up to 64K or more per OmniSwitch 9000 chassis. 
The 6.1.3.R01 release provides support for this feature on the OmniSwitch 9000 Series. 
10Mbps Connections supported 
10BASE-T hub or device 
100Mbps Connections supported 
100BASE-TX hub or device 
1000Mbps Connections supported 
1000BASE-T connections to backbone or server 
10Mbps Cables supported 
10BASE-T: unshielded twisted-pair (UTP) 
100Mbps Cables supported 
100BaseTX: unshielded twisted-pair (UTP), Category 5, EIA/TIA 568 or shielded twisted-pair (STP),  
Category-5, 100 ohm 
1000Mbps Cables supported 
1000BASE-T: unshielded twisted-pair (UTP), and Category 5/5e 
Maximum Cable Distance 
100 meters on Category 5 
Power consumption 
54watts 
Default amount of inline power 
allocated per switch slot 
210 watts 
(please note that 
future
 enhancements will provide more PoE power per slot and/or per module) 
Default amount of inline power 
allocated for each port 
15400 Milliwatts (15.4 watts) 
Range of inline power allowed for 
each port 
3000–18000 Milliwatts (3 watts to 18 watts) 
Power Over Ethernet (PoE) 
IEEE 802.3af (requires OS9-GNI-P24 & PoE shelf) 
Maximum (assuming no P/S redundancy) power of 2100W: 
(4 x (600W - PSU-overhead=525W)) using the OS9-IP-SHELF 
(please note that 2400watts of PoE power will be supported in 
a future release
Maximum power of 230W / 390W using the OS9-IPS-0230A/ OS9-IPS-0390A (used exclusively on the 
OS9600 chassis type) 
The 510W and 360W (aka. 230W/390W) power supplies can be used as an alternate power source for PoE. A 
single 510W power supply allocates 390W for the PoE functionality; similarly, a single 360W power supply 
allocates 230W for the PoE functionality. Only one power supply module can be installed per switch, not both. 
These power modules do not support load sharing. 
Note. The 360W/510W power supplies are only supported on OS9600 switches and not on OS9700/OS9800 
switches.