Akai MPC STUDIO 사용자 설명서

 

26.

 

SEQ EDIT / EFFECTS – Press this button to enter Sequence Edit mode. Hold down SHIFT and press this 
button to enter Effects mode, where you can select and route effects as well as edit effects' parameters.  

27.

 

SAMPLE EDIT / SAMPLE REC – Press this button to view the Sample Edit screen in the display and 
software. Hold down SHIFT and press this button to view the Sample Record screen in the display and 
software. 

28.

 

SONG / OTHER – Press this button to view the Song screen in the display and software. Hold down SHIFT 
and press this button to enter Other mode, which allows you to set: the minimum number of taps for the 
TAP TEMPO button; pad threshold, sensitivity, and curve; the footswitches' messages; and the Program 
Change target. 

29.

 

STEP SEQ – Press this button to view the Step Sequence screen in the display and software.  

30.

 

NEXT SEQ – Press this button to view the Next Sequence screen in the display and software.  

31.

 

TRACK MUTE / PAD MUTE – Press this button to view the Track Mute screen in the display and software. 
Hold SHIFT and press this button to view the Pad Mute screen in the display and software. 

32.

 

WINDOW / FULL SCREEN – When this button is lit, it means the selected field in the display contains 
additional functions; press this button to access them. Use the F-BUTTONS, CURSOR BUTTONS, and 
DATA DIAL or -/+ buttons to execute (or cancel) these additional functions. 
Hold SHIFT and press this button to switch between Full Screen and Half Screen modes. In Full Screen 
mode, the workspace occupies the whole screen. In Half Screen mode, the parameter controls (Q-Link 
knobs, pads, Sequence and Track information, Project Information, etc.) are shown underneath the 
workspace. 

33.

 

PROJECT / FOLDER 1 – Press this button to view only Project files in the File Browser. Hold down SHIFT 
and press this button to select the Browser's Folder 1 shortcut. 

34.

 

SEQUENCE / FOLDER 2 – Press this button to view only Sequence files in the File Browser. Hold down 
SHIFT and press this button to select the Browser's Folder 2 shortcut. 

35.

 

PROGRAM / FOLDER 3 – Press this button to view only Program files in the File Browser. Hold down 
SHIFT and press this button to select the Browser's Folder 3 shortcut. 

36.

 

SAMPLE / FOLDER 4 – Press this button to view only Sample files in the File Browser. Hold down SHIFT 
and press this button to select the Browser's Folder 4 shortcut. 

37.

 

NO FILTER / FOLDER 5 – Press this button to view all files in the File Browser. Hold down SHIFT and 
press this button to select the Browser's Folder 5 shortcut. 

 

 
38.

 

PLAY – Press this button to play the Sequence from the audio pointer's current position. 

39.

 

PLAY START – Press this button to play the Sequence from its start point. 

40.

 

STOP – Press this button to stop playback. 

41.

 

REC – Press this button to record-arm the Sequence. Press PLAY or PLAY START to start recording. 
Recording in this way (rather than using OVERDUB) erases the events of the current Sequence. After the 
Sequence plays through once while recording, Overdub will be enabled.  

42.

 

OVERDUB – Press this button to enable Overdub, which allows you to record note events in a Sequence 
without overwriting any previously recorded note events. You can enable Overdub either before or during 
recording. 

43.

 

< / > ( |< / >| ) – Use these buttons to move the audio pointer left/right, one step at a time. Hold LOCATE 
and press one of these buttons to move the audio pointer to the previous/next event in the Sequence Grid. 

44.

 

<< / >> (START/END) – Use these buttons to move the audio pointer left/right, one bar at a time. Hold 
LOCATE and press one of these buttons to move the audio pointer to the start or end of the Sequence 
Grid. 

45.

 

GO TO – Hold this button down to activate the secondary functions of the < / > and << / >> buttons (i.e., |< 
/ >| and START/END, respectively). 

46.

 

ERASE – As a Sequence is playing, hold this button down and press a pad to delete the note event for that 
pad at the current playback position. This is a quick way to delete note events from your Sequence without 
having to stop playback. 

47.

 

TAP TEMPO – Press this button in time with the desired tempo to enter a new tempo (in BPM) in the 
software. 

 

 
For additional information, technical support, and the most current versions of software, firmware, or drivers, 
please visit: