Hameg HM800 Empty module HM 800 24-0800-0000 데이터 시트
제품 코드
24-0800-0000
Subject to change without notice
5
I m p o r t a n t h i n t s
Important hints
The operator is requested to read the following
instructions and those of the mainframe HM8001-
2 carefully, to avoid any operating errors and
mistakes and in order to become acquaint with
the module.
instructions and those of the mainframe HM8001-
2 carefully, to avoid any operating errors and
mistakes and in order to become acquaint with
the module.
After unpacking the blank module, check for any
mechanical damage or loose parts inside. Should
there be any transportation damage, inform the
supplier immediately and do not put the module
into operation. This plug-in module is primarily
intended for use in conjunction with the mainfra-
me HM8001-2. When incorporating it into other
systems, the module should only be operated with
the specifi ed supply voltages.
mechanical damage or loose parts inside. Should
there be any transportation damage, inform the
supplier immediately and do not put the module
into operation. This plug-in module is primarily
intended for use in conjunction with the mainfra-
me HM8001-2. When incorporating it into other
systems, the module should only be operated with
the specifi ed supply voltages.
Safety
This instrument has been designed and tested in
accor dance with IEC Publication 1010-1, Safety
require ments for electrical equipment for measu-
rement, control, and laboratory use. It corres-
ponds as well to the CENELEC regulations EN
61010-1. All case and chassis parts are connected
to the safety earth conductor. Corresponding to
Safety Class 1 regulations (three-conductor AC
power cable). Without an isolating transformer,
the instrument's power cable must be plugged
into an approved three-contact electrical outlet,
which meets International Electrotechnical Com-
mission (IEC) safety standards.
accor dance with IEC Publication 1010-1, Safety
require ments for electrical equipment for measu-
rement, control, and laboratory use. It corres-
ponds as well to the CENELEC regulations EN
61010-1. All case and chassis parts are connected
to the safety earth conductor. Corresponding to
Safety Class 1 regulations (three-conductor AC
power cable). Without an isolating transformer,
the instrument's power cable must be plugged
into an approved three-contact electrical outlet,
which meets International Electrotechnical Com-
mission (IEC) safety standards.
Warning!
Any interruption of the protective conductor
inside or outside the instrument or discon-
nection of the protective earth terminal is
likely to render the instrument dangerous.
Intentional interruption is prohibited.
Any interruption of the protective conductor
inside or outside the instrument or discon-
nection of the protective earth terminal is
likely to render the instrument dangerous.
Intentional interruption is prohibited.
The istrument must be disconnected and secured
against unintentional operation if there is any sug-
gestion that safe operation is not possible.
against unintentional operation if there is any sug-
gestion that safe operation is not possible.
This may occur:
– if the instrument shows visible damage,
– if the instrument has loose parts.
– if the instrument does not function,
– after long storage under unfavourable circ-
– if the instrument shows visible damage,
– if the instrument has loose parts.
– if the instrument does not function,
– after long storage under unfavourable circ-
umstances (e.g. outdoors or in moist environ-
ments),
ments),
– after excessive transportation stress (e.g. in
poor packaging).
When removing or replacing the metal case, the
instrument must be completely disconnected
from the mains supply. If any measurement or
calibration procedures are necessary on the
opened-up instrument, these must only be carried
out by qualifi ed personnel acquainted with the
danger involved.
instrument must be completely disconnected
from the mains supply. If any measurement or
calibration procedures are necessary on the
opened-up instrument, these must only be carried
out by qualifi ed personnel acquainted with the
danger involved.
Symbols marked on equipment
ATTENTION refer to manual.
DANGER! High voltage.
Protective ground (earth) terminal.
Operating conditions
The ambient temperature range during operation
should be between +5°C and +40 °C and should
not exceed –20 °C or +70 °C during transport or
storage. The operational position is optional, how-
ever, the ventilation holes on the HM8001-2 and on
the plug-in modules must not be obstructed.
should be between +5°C and +40 °C and should
not exceed –20 °C or +70 °C during transport or
storage. The operational position is optional, how-
ever, the ventilation holes on the HM8001-2 and on
the plug-in modules must not be obstructed.
Warranty and Repair
HAMEG instruments are subjected to a strict qua-
lity control. Prior to leaving the factory, each ins-
trument is burnt-in for 10 hours. By intermittent
operation during this period almost all defects are
detected. Following the burn-in, each instrument
is tested for function and quality, the specifi cations
are checked in all operating modes; the test gear
is calibrated to national standards.
lity control. Prior to leaving the factory, each ins-
trument is burnt-in for 10 hours. By intermittent
operation during this period almost all defects are
detected. Following the burn-in, each instrument
is tested for function and quality, the specifi cations
are checked in all operating modes; the test gear
is calibrated to national standards.
The warranty standards applicable are those of
the country in which the instrument was sold.
Reclamations should be directed to the dealer.
the country in which the instrument was sold.
Reclamations should be directed to the dealer.
Only valid in EU countries
In order to speed reclamations customers in EU
countries may also contact HAMEG directly. Also,
after the warranty expired, the HAMEG service will
be at your disposal for any repairs.
In order to speed reclamations customers in EU
countries may also contact HAMEG directly. Also,
after the warranty expired, the HAMEG service will
be at your disposal for any repairs.