Weigel Mains-analysis device, Mains analyser 6790006 데이터 시트
제품 코드
6790006
Application
The digital Weigel Power Meters have been designed to display the
electrical parameters in low voltage systems. The meters are suitable for
use in 3 - phase 3 - wire or 3 - phase 4 - wire systems 230/400 V and for
use with current transformers N/5 A.
electrical parameters in low voltage systems. The meters are suitable for
use in 3 - phase 3 - wire or 3 - phase 4 - wire systems 230/400 V and for
use with current transformers N/5 A.
D WPM 735 E-H-T-AO-V3 is equipped with harmonics analysis, SOE
(event monitoring) as well as 8 status inputs, 2 pulse outputs and
1 analog output
1 analog output
D WPM 735 P-H-V3 is equipped with harmonics analysis and Profibus
The panel meters display the electrical parameters in the network:
voltages phase to neutral and phase to phase, currents of the 3 phases,
neutral current; unbalance rates for currents and voltages; active power,
reactive power, apparent power and power factor of the 3 phases and in
total; frequency; active energy and reactive energy in 4 quadrants (im-
ported/exported, inductive/capacitive); demand and maximum demand
of the currents and powers; harmonics of current and voltage up to the
31
The panel meters display the electrical parameters in the network:
voltages phase to neutral and phase to phase, currents of the 3 phases,
neutral current; unbalance rates for currents and voltages; active power,
reactive power, apparent power and power factor of the 3 phases and in
total; frequency; active energy and reactive energy in 4 quadrants (im-
ported/exported, inductive/capacitive); demand and maximum demand
of the currents and powers; harmonics of current and voltage up to the
31
st
harmonics as well as total harmonic distortion (THD). Various rat-
ings are displayed at the same time and can be selected by pressing
buttons.
buttons.
Special events SOE (Status of Events) are recorded with date and time
stamp.
stamp.
Using the integrated RS485 or Profibus interface, all measured ratings
and the events can be read out and settings can be made.
Software for read out and configuration is available via download from
www.weigel-messgeraete.de
and the events can be read out and settings can be made.
Software for read out and configuration is available via download from
www.weigel-messgeraete.de
Using the front - side buttons, the voltage and current transformer ratios,
the system type and communication parameters can be set and the en-
ergy counters and demand values can be reset.
the system type and communication parameters can be set and the en-
ergy counters and demand values can be reset.
Functional Principle
WPM 735 is a microprocessor-controlled digital measuring device for
measuring, calculating, and indicating electrical ratings.
measuring, calculating, and indicating electrical ratings.
The meter has 3 voltage inputs and 3 current inputs to enable simulta-
neous evaluation of voltage, current and power for all three phases.
neous evaluation of voltage, current and power for all three phases.
The meter must be connected via current transformers.
General Technical Data
Case
case details
suitable to be mounted in switch gear panels
material of case
plastics, black
panel fixing
plastic clips
enclosure code
IP 50 front of case
IP 20 rear of case
IP 20 rear of case
insulation voltage
2 kV AC
inputs – outputs – auxiliary supply
inputs – outputs – auxiliary supply
pulse withstand
5 kV (peak), 1.2/50
mS
voltage
insulation resistance
≥50 MW
MTBF
≥50000 h
operating elements
6 buttons
Terminals
3 plugable screw-terminal barrier strips
wire-cross section
2.5 mm
2
max.
Dimensions
bezel
V 96 mm
bezel height
18 mm
panel cutout
V 90
+0.5
mm
mounting depth
80 mm minus panel thickness
panel thickness
5 mm
weight
approx. 0,7 kg
Electrical Data
system type
3 - phase 3 - wire or 3 - phase 4 - wire system,
unbalanced loads
unbalanced loads
rated voltage
230/400 V
PT ratio
adjustable 1 to 2500
rated current
5 A
current connection
via CTs N/5 A
CT ratio
adjustable 1 to 10000
overload capacity
current
1.2 times continously
10 times for 1 sec.
10 times for 1 sec.
voltage
1.2 times continously
2 times for 1 sec.
2 times for 1 sec.
frequency range
35 ... 65 Hz
Auxiliary Supply
auxiliary voltage
85 ... 265 V AC (45 ... 65 Hz) or 100 ... 300 V DC
power consumption
<3 VA
Display/Measuring/Accuracy
display
LCD display, green, 65 mm x 65 mm
with backlight (when pressing a button)
with backlight (when pressing a button)
Measured quantities
voltages
U
L-L and L-N
currents
I
L1, L2, L3 and N
active power
P
L1, L2, L3 and
SP
reactive power
Q
L1, L2, L3 and
SQ
apparent power S
L1, L2, L3 and
SS
power factor
PF
L1, L2, L3 and in total
frequency
F
F
active energy
imported and exported
reactive energy
induktive and capacitive
demand and maximum demand of currents and powers
demad time
demad time
15 min (fixed)
unbalance rates of voltages und currents
recording of maximum and minimum ratings of I, P, Q, S
individual harmonics of current and voltage up to the 31
recording of maximum and minimum ratings of I, P, Q, S
individual harmonics of current and voltage up to the 31
st
harmonics
THD
total harmonic distortion
Measuring unit
Display range
Resolution Accuracy
voltages (L-L, L-N)
0 ... 500 kV
0.01 V
0.2%
currents (L1, L2, L3, N)
0 ... 50 kA
0.001 A
0.2%
active power
0 ...
±100 MW
0.1 W
0.5%
reactive power
0 ...
±100 MVar
0.1 Var
0.5%
apparent power
0 ...
±100 MVA
0.1 VA
0.5%
power factor
–1 ... +1 ... –1
0.001
0.5%
frequency
35 ... 65 Hz
0.01 Hz
0.1%
active energy
*
)
0 ... 99,999,999.9 kWh
0.1 kWh
1.0%
reactive energy
*
) 0 ... 99,999,999.9 kVarh
0.1 kVarh
2.0%
unbalance rate
0 ... 100.0%
0.001
1.0%
individual harmonics
0 ... 100.0%
0.001
1.0%
THD
0 ... 100.0%
0.001
1.0%
*
) The accuracy for energy measurement is class 1
according to IEC 62053–21.