Technoline WS 9032 데이터 시트
21
at start-up. This code must be received and stored by the Weather Station in the first 3
minutes of power being supplied to the transmitter.
minutes of power being supplied to the transmitter.
BATTERY CHANGE:
It is recommended to replace the batteries in all units on an annual basis to ensure optimum
accuracy of these units.
accuracy of these units.
Please participate in the preservation of the environment. Return used
batteries to an authorized depot.
batteries to an authorized depot.
SETTING UP
WHEN ONE TRANSMITTER IS USED
1.
First, insert the batteries in the transmitter (see “How to install and replace batteries
in the Termo-hygro outdoor transmitter” above).
in the Termo-hygro outdoor transmitter” above).
2.
Within 2 minutes of powering up the transmitter, insert the batteries in the Temperature
Station (see “How to install and replace batteries in the Weather Station” above).
Once the batteries are in place, all segments of the LCD will light up briefly and a short
signal tone will sound. Following the indoor temperature/humidity and the time as 0:00
will be displayed. If these information are not displayed on the LCD after 60 seconds,
remove the batteries and wait for at least 60 seconds before reinserting them. Once
the indoor data is displayed user may proceed to the next step.
Station (see “How to install and replace batteries in the Weather Station” above).
Once the batteries are in place, all segments of the LCD will light up briefly and a short
signal tone will sound. Following the indoor temperature/humidity and the time as 0:00
will be displayed. If these information are not displayed on the LCD after 60 seconds,
remove the batteries and wait for at least 60 seconds before reinserting them. Once
the indoor data is displayed user may proceed to the next step.
3.
After the batteries are inserted, the Weather station will start receiving data signal from
the transmitter. The outdoor temperature and humidity data should then be displayed
on the Weather station. If this does not happen after 2 minutes, the batteries will need
to be removed from both units and reset from step 1.
the transmitter. The outdoor temperature and humidity data should then be displayed
on the Weather station. If this does not happen after 2 minutes, the batteries will need
to be removed from both units and reset from step 1.
4.
In order to ensure sufficient 868 MHz transmission however, the distance between the
Weather Station and the transmitter should not be more than 100 meters (see notes on
“Positioning” and “868 MHz Reception”).
Weather Station and the transmitter should not be more than 100 meters (see notes on
“Positioning” and “868 MHz Reception”).
Note:
In the event of changing batteries of the units, ensure the batteries do not spring free from
the contacts. Always wait at least 1 minute after removing the batteries before reinserting,
otherwise start up and transmission problems may occur.
In the event of changing batteries of the units, ensure the batteries do not spring free from
the contacts. Always wait at least 1 minute after removing the batteries before reinserting,
otherwise start up and transmission problems may occur.
WHEN MORE THAN ONE TRANSMITTER IS USED
1.
User shall remove all the batteries from the Weather Station and transmitters, and wait
60 seconds.
60 seconds.
2.
Insert the batteries in the first transmitter.
3.
Within 2 minutes of powering up the first transmitter, insert the batteries in the Weather
Station. Once the batteries are in place, all segments of the LCD will light up briefly
and a short signal tine will sound. Following the indoor temperature/humidity and the
time as 0:00 will be displayed. If these information are not displayed on the LCD after
60 seconds, remove the batteries from both units and wait for at least 60 seconds
before reinserting them.
Station. Once the batteries are in place, all segments of the LCD will light up briefly
and a short signal tine will sound. Following the indoor temperature/humidity and the
time as 0:00 will be displayed. If these information are not displayed on the LCD after
60 seconds, remove the batteries from both units and wait for at least 60 seconds
before reinserting them.
4.
The outdoor temperature and humidity data from the first transmitter (channel 1)
should then be displayed on the Weather Station. Also, the signal reception icon will be
displayed. If this does not happen after 2 minutes, the batteries will need to be
removed from both units and reset from step 1.
should then be displayed on the Weather Station. Also, the signal reception icon will be
displayed. If this does not happen after 2 minutes, the batteries will need to be
removed from both units and reset from step 1.
5.
Insert the batteries in the second transmitter as soon as the outdoor temperature and
humidity readings from the first transmitter are displayed on the Weather Station.
Note :
humidity readings from the first transmitter are displayed on the Weather Station.
Note :
User shall insert the batteries into the second transmitter within 45 seconds
after the Weather Station displays the information of the first transmitter.
6.
The outdoor temperature and humidity from the second transmitter and the "channel 2"