Scorpion Infrared Remote Control IR Transmitter 전단
제품 코드
IR Transmitter
1.0 Connecting your Scorpion ESC
to the programming card
Your Scorpion ESC is programmed using the Infrared (IR) Program card and
Receiver with this ESC. First you must connect your IR Receiver to your
ESC. Ensure the brown wire from your ESC is facing outwards.
To program any function on the card you must follow the following procedure:
Example LOW Voltage Cut to enter 13V:
Press a function button
6.1
Enter a numeric value
6.2
Enter to complete
6.3
Please note that there is a time limit from when you press a function button
the numeric values and enter if you go over this time limit no sound of
flashes will come from the ESC.
If successful a DI DOO sound will come from the motor and the LED will Flash
RED. An invalid option will not get any confirmation sound from the motor
and the LED will not flash.
BN
PPM
IRS
D1
IC2
Q2
BROWN
IRRECV2
SW1
CN2
C1
Q1
To Receiver
Switch
From ESC
Please note that IR will be interfered in direct sunlight so to program
your model we suggest doing it indoors in the shade out of direct sunlight.
Once you have plugged in the IR Receiver push the switch across to IRS.
5.1
Now connect a battery to the ESC. Your Motor will emit 3 beeps and
the LED will flash 3 times red, (In 15V Series ESC, no LED is installed
and only emit 3 beeps).
5.2
Your IR Receiver is now ready to receive a signal from the program card
5.3
Before flying you will need to place the switch back to PPM mode.
2.0 Using the Programming Card
All parameters of the ESC can be changed via the program card.
P.GAIN
I.GAIN
To reset all parameters to Factory Default:
page 2
page 3
*Factory Default
Definition of Function Buttons
Function Button
Example from
Above
LVC 15V LBEC ESC
LVC 15V LBEC ESC
(Low Voltage Cut)
LVC 17V SBEC ESC
(Low Voltage Cut)
LVC 50V ESC
(Low Voltage Cut)
LVC 68V ESC
LVC 68V ESC
(Low Voltage Cut)
BRK
(Brake Setting)
PCT
Program Cut Type
(LVC type)
CAR/B
Car/Boat Mode
COP
COP
Current Overload
Protection
FREQ
Drive Frequency
SS
(Heli Mode /
Soft Start Mode)
See section 8.0
RO
Motor Rotation
Direction
TIM
Motor Timing
I.GAIN
P.GAIN
ENTER
OTHER
MAT
Motor
Acceleration Time
Delay
AIR
Numeric
value
130
050-135
050-135
120-480
120-560
1*
2
3
4
5
1*
2
3
Disable
Disable
1*
2
1*
1
2
1*
2
3
4
5
6
1~8
5*
1*
2
3
1~11
5*
1
2*
3
4
5
1*
What it does
Sets Low Voltage Cut to 13.0 Volts.
Low Voltage Cut 050 (5V) to 135
(13.5V) in 0.5 V increments. *6V
Low Voltage Cut 050 (5V) to 135
(13.5V) in 0.5 V increments. *6V
Low Voltage Cut 120 (12V) to 480
(48V) in 0.5 V increments. *12V
Low Voltage Cut 120 (12V) to 560
(56V) in 0.5 V increments. *12V
*No brake
Very soft brake
Soft Brake
Hard Brake
Very Hard Brake
Cut 50% of maximum power
No Cut just LED warning
Pulse warning
No Function is Available
No Function is Available
Protection on
warranty)
8k Hz
Heli mode with soft start, Variable
throttle adjustable Soft start.
Heli mode with soft start and
governor. (See Governor Section)
Auto Timing
5°
15°
20°
25°
30°
Sensitive~Insensitive
15 Seconds
25 Seconds
35 Seconds
Soft~Hard
Enter value send signal to ESC
All other keys are reserved for
future programming options
0.15 second
0.3 second
0.45 second
0.7 second
1.3 second
Activate Airplane mode
Auto Rotation
(Bail Out Time)
Scorpion
User Guide for
Commander Series ESC’s
V-700
IR Receiver
IR Programming Card