Texas Instruments TLV320AIC1103EVM-K Evaluation Module TLV320AIC1103EVM-K TLV320AIC1103EVM-K 데이터 시트
제품 코드
TLV320AIC1103EVM-K
Power Supplies
www.ti.com
4
Power Supplies
J3 provides connection to the common power bus for the TLV320AIC11xxEVM. Power is supplied on the
pins listed in
pins listed in
.
Table 4. Power Supply Pinout
SIGNAL
PIN NUMBER
SIGNAL
NC J3.1
J3.2
NC
+5VA J3.3
J3.4
NC
DGND J3.5
J3.6
AGND
NC J3.7
J3.8
NC
IOVDD (3.3V) J3.9
J3.10
NC
The TLV320AIC11xxEVM-K motherboard (the USB-MODEVM Interface board) supplies power to J3 of the
TLV320AIC11xxEVM. Power for the motherboard is supplied either through its USB connection or via
terminal blocks on that board.
TLV320AIC11xxEVM. Power for the motherboard is supplied either through its USB connection or via
terminal blocks on that board.
4.1
Stand-Alone Operation
When used as a stand-alone EVM, power can be applied to J3 directly. The user must be sure to
reference the supplies to the appropriate grounds on that connector.
reference the supplies to the appropriate grounds on that connector.
CAUTION
Verify that all power supplies are within the safe operating limits shown on the
product datasheet before applying power to the EVM.
product datasheet before applying power to the EVM.
4.2
USB-MODEVM Interface Power
The USB-MODEVM Interface board can be powered from several different sources:
•
•
USB
•
6VDC–10VDC AC/DC external wall supply (not included)
•
Lab power supply
When powered from the USB connection, JMP6 should have a shunt from pins 1–2 (this is the default
factory configuration). When powered from 6V-10VDC, either through the J8 terminal block or the J9
barrel jack, JMP6 should have a shunt installed on pins 2-3. If power is applied in any of these ways,
onboard regulators generate the required supply voltages and no further power supplies are necessary.
factory configuration). When powered from 6V-10VDC, either through the J8 terminal block or the J9
barrel jack, JMP6 should have a shunt installed on pins 2-3. If power is applied in any of these ways,
onboard regulators generate the required supply voltages and no further power supplies are necessary.
If lab supplies are used to provide the individual voltages required by the USB-MODEVM Interface, JMP6
should have no shunt installed. Voltages are then applied to J2 (+5VA), J3 (+5VD), J4 (+1.8VD), and J5
(+3.3VD). The +1.8VD and +3.3VD can also be generated on the board by the onboard regulators from
the +5VD supply; to enable this configuration, the switches on SW1 need to be set to enable the
regulators by placing them in the ON position (lower position, looking at the board with text reading
right-side up). If +1.8VD and +3.3VD are supplied externally, disable the onboard regulators by placing
SW1 switches in the OFF position.
should have no shunt installed. Voltages are then applied to J2 (+5VA), J3 (+5VD), J4 (+1.8VD), and J5
(+3.3VD). The +1.8VD and +3.3VD can also be generated on the board by the onboard regulators from
the +5VD supply; to enable this configuration, the switches on SW1 need to be set to enable the
regulators by placing them in the ON position (lower position, looking at the board with text reading
right-side up). If +1.8VD and +3.3VD are supplied externally, disable the onboard regulators by placing
SW1 switches in the OFF position.
Each power supply voltage has an LED (D1-D7) that lights when the power supplies are active.
5
EVM Operation
This section provides information on the analog input and output, digital control, and general operating
conditions for the TLV320AIC11xxEVM.
conditions for the TLV320AIC11xxEVM.
5.1
Analog Input
The analog input sources can be applied directly to J2 (top or bottom side). The analog inputs may also
be accessed through J8 and screw terminals J9 and J10.
be accessed through J8 and screw terminals J9 and J10.
6
TLV320AIC1103/1110EVM-K
SLAU297A – November 2009 – Revised January 2011
© 2009–2011, Texas Instruments Incorporated