Texas Instruments TMS320C6472 Evaluation Module TMDSEVM6472LE TMDSEVM6472LE 데이터 시트
제품 코드
TMDSEVM6472LE
PRODUCTPREVIEW
SPRS612G
–
JUNE 2009
–
REVISED JULY 2011
3.3
Peripheral Selection After Device Reset
3.3.1
Controlling Internal Pulls on the Peripherals
3.3.1.1
Device Control Register (DEVCTL)
The device control register (DEVCTL) controls the internal pulls on the I/O interfaces. The bits are
initialized on the rising edge of the Power-On Reset from the GPIO pins [5:0], then software can override
these latched values. When the DSP is out of reset, the DEVCTL bits control the pullup and pulldown
resistors. When the DSP is held in reset, the GPIO pins enable the pullup and pulldown resistors, directly.
These bits also enable or disable the output buffers on these interfaces. When the pull-up or pull-down
resistors are enabled, the output buffers are disabled. When not in use, all the inputs should be in a
known state (i.e., needs to be internally pulled) and the corresponding I/O buffers should be powered
down to save I/O power. The DEVCTL register is shown in
initialized on the rising edge of the Power-On Reset from the GPIO pins [5:0], then software can override
these latched values. When the DSP is out of reset, the DEVCTL bits control the pullup and pulldown
resistors. When the DSP is held in reset, the GPIO pins enable the pullup and pulldown resistors, directly.
These bits also enable or disable the output buffers on these interfaces. When the pull-up or pull-down
resistors are enabled, the output buffers are disabled. When not in use, all the inputs should be in a
known state (i.e., needs to be internally pulled) and the corresponding I/O buffers should be powered
down to save I/O power. The DEVCTL register is shown in
and described in
contains more detail about the operation of the internal resistor pulls and the output buffer
operation. It explicitly lists the relevant pins individually under all possible configurations and states
whether the output buffers are enabled or disabled and whether the internal pull resistors are enabled or
disabled.
whether the output buffers are enabled or disabled and whether the internal pull resistors are enabled or
disabled.
31
16
Reserved
R-0000 0000
15
13
12
11
9
8
Reserved
EMAC1_EN
TSIP2_EN[2:0]
TSIP1_EN2
R/W-0
R/W-x
R/W-xxx
R/W-xxx
7
6
5
3
2
1
0
TSIP1_EN[1:0]
TSIP0_EN[2:0]
UTOPIA_EN[1:0]
HPI_EN
R/W-xxx
R/W-xxx
R/W-xx
R/W-x
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Figure 3-1. Device Control Register (DEVCTL)
Table 3-3. Device Control Register (DEVCTL) Field Descriptions
Bit
Field
Value
Description
31:13
Reserved
Reserved
12
EMAC1_EN
EMAC1 Internal Pulls Enable. Initialized at reset from GP05/EMAC1_EN pin.
0
Enable the pulls on the 3.3-V EMAC1 I/O pins and power down the corresponding I/O buffers. Also
disable the EMAC1 RGMII I/O pins.
disable the EMAC1 RGMII I/O pins.
1
Allow the pulls on the 3.3-V EMAC1 I/O to be disabled and the corresponding I/O buffers to be
powered up. Also allow the RGMII I/O buffers to be powered up. This input is combined with the
MACSEL1[1:0] configuration inputs to determine which I/O pins are enabled and which are
disabled. All disabled 3.3-V I/O pins will have internal pulls active.
powered up. Also allow the RGMII I/O buffers to be powered up. This input is combined with the
MACSEL1[1:0] configuration inputs to determine which I/O pins are enabled and which are
disabled. All disabled 3.3-V I/O pins will have internal pulls active.
11
TSIP2_EN[2]
TSIP2 Internal Pulls Enable[2]. Initialized at reset from GP04/TSIP2_EN pin.
0
Enable the pulls on TX[7:4] and TR[7:4] of the TSIP2 I/O pins and power down the corresponding
I/O buffers.
I/O buffers.
1
Disable the pulls on TX[7:4] and TR[7:4] of the TSIP2 I/O pins and power up the corresponding I/O
buffers.
buffers.
10
TSIP2_EN[1]
TSIP2 Internal Pulls Enable[1]. Initialized at reset from GP04/TSIP2_EN pin.
0
Enable the pulls on TX[3:2] and TR[3:2] of the TSIP2 I/O pins and power down the corresponding
I/O buffers.
I/O buffers.
1
Disable the pulls on TX[3:2] and TR[3:2] of the TSIP2 I/O pins and power up the corresponding I/O
buffers.
buffers.
Copyright
©
2009
–
2011, Texas Instruments Incorporated
Device Configuration
63
Product Folder Link(s) :