Benning TRITEST pro Multi-Tester 020052 데이터 시트

10/ 2014 

® 

pro 

 



-  During the tests, touch the device at the insulated 

test probes 9,   and  only and do not touch 

the bare testing electrodes 8! 

-  Check the device for correct functioning immedi-

ately before and after using it (see section 3)! Do 

not use the device, if one or more indications are 

not working or if it does not seem to be ready for 

operation!

-  If it is assumed that safe operation is no longer 

possible, the device must be switched off immedi-

ately. 

-  Absolutely prevent the device from getting wet 

and avoid any water condensation at the device. 

Moreover, the device must be protected against 

contamination and damaging! 

-  The device must be used within the stated nomi-

nal voltage range and in electrical installations of 

up to 500 V AC only! 

-  The device must be used only in electric circuits 

of overvoltage category CAT III with max. 300 V 

for phase-to-earth measurements. For measure-

ments within measuring category III, the protrud-

ing conductive part of a testing electrode 8 of the 

test probe must not be longer than 4 mm. Before 

carrying out measurements within measuring cat-

egory III, the enclosed attachable protective caps 

marked with CAT III must be pushed onto the test-

ing electrodes 8 for user protection purposes.

-   Please observe that work on live parts and elec-

trical components of all kinds is dangerous! Even 

low voltages of 30 V AC and 60 V DC may be 

dangerous to human life!

-   Do not operate the device with the battery com-

partment being open.

-  The device is designed for being used by qualified 

electricians and under safe working conditions. 

-   Do not dismantle the device! 

The device is provided with a high-power LED torch. 

Do not look directly or indirectly via reflecting surfaces 

into the LED beam. An LED beam might cause irrepa-

rable damage to your eyes.

Symbols on the device: 

Symbol

Meaning



Attention! Please observe documenta-

tion!

This symbol indicates that the informa-

tion provided in the operating manual 

must be complied with in order to avoid 

risks.



Alternating voltage (AC)



Earth (voltage to earth)
This symbol shows the orientation of the 

batteries for inserting them with correct 

polarity.
Warning! Potentially dangerous optical 

radiation!

Do not look directly into the light beam! 

Danger to your retina!
Attention! Magnets might affect the cor-

rect functioning of cardiac pacemakers 

and implanted defibrillators. As a user of 

such medical devices, keep a sufficient 

distance to the magnet.

1

  Red LED for external conductor (phase) L1

2

  Red LED for external conductor (phase) L2

3

  Red LED for external conductor (phase) L3

4

  Red LED for counter-clockwise phase sequence

5

  Green LED for clockwise phase sequence

6

  High-power LED torch 

7

 Push-button

8

  Testing electrodes with attachable protective caps

9

  Test probe L1 (brown), part no.: 10112582



  Test probe L2 (black), part no.: 10112581



  Test probe L3 (grey), part no.: 10112584



  Alligator clip, part no.: 709269



  Catch of the battery compartment cover



  Battery compartment cover with magnet, belt clip 

and technical data

-  Check the device for correct functioning immedi-

ately before and after using it! 

-  Test the correct functioning of the LEDs 1,  2 

and  3 for indicating the external conductors L1, 

L2 and L3 as well as the LEDs 4 and 5 of the 

phase sequence indication with a familiar voltage 

source, e.g. a 400 V CEE socket.

-  Do not use the device, if not all functions are 

working properly!

-  Please replace the batteries as soon as the lumi-

nosity of the LED torch 6 decreases.

-  Connect the connecting cables marked with L1, 

L2 and L3 to the mains to be tested. For this pur-

pose, use the test probes 9,  and  or the alli-

gator clip . 

-  The external conductor voltages are indicated by 

means of the red LEDs 1, 2 and 3.

-  Depending on the connection, the red LED (4) for 

"counter-clockwise phase sequence" or the green 

LED  5 for "clockwise phase sequence" will be 

activated.

-  Interchanging the test probes on two external 

conductors must result in a change of the phase 

sequence.

-  For each test, make sure that all three external 

conductor voltages are present. Only then, the 

indicated results can be analyzed!

tritest-pro_d3.indd   3

24.10.2014   09:08:45