C Control I Micro-PCB 5 V/DC, 12 Vdc Inputs / outputs 1 x digital I/O / 1 x digital input / 4 x digital I/O or analogue 198289 데이터 시트
제품 코드
198289
72
MINUTE (0...59)
SECOND (0...59)
Please observe the fact that the internal clock continues to run during access. The
second value should therefore always be read first. If it shows 59 it is necessary that
after reading the last interesting time information (e.g. HOUR) the second value is
read again and test for =O. In this case, the real-time clock has to be read again as a
new minute has been started.
second value should therefore always be read first. If it shows 59 it is necessary that
after reading the last interesting time information (e.g. HOUR) the second value is
read again and test for =O. In this case, the real-time clock has to be read again as a
new minute has been started.
Further-reaching time information is not available in the C-control MICRO but can if
necessary be generated by means of a small sub-program-
necessary be generated by means of a small sub-program-
EXACTITUDE:
The RTC of the C-CONTROL MICRO is fed from a free-running oscillator which in
principle cannot fulfil the demands on a precise clock. The manufacturer states
exactitude of 25 %. So that the RTC remains usable nevertheless, you have the pos-
sibility of calibrating the clock’s cycle.
The tool CLOCK_CHECK.BAS will help you in calibrating and will also give you fur-
ther tips.
The RTC of the C-CONTROL MICRO is fed from a free-running oscillator which in
principle cannot fulfil the demands on a precise clock. The manufacturer states
exactitude of 25 %. So that the RTC remains usable nevertheless, you have the pos-
sibility of calibrating the clock’s cycle.
The tool CLOCK_CHECK.BAS will help you in calibrating and will also give you fur-
ther tips.
FREQ2=value
writes a correction factor into the operating system which corrects the system cycle
by 0.2% per digit (starting from the default value 128 after RESET). This allows the
cycle to be set to an exactitude of 0.2% which corresponds to an error in the RTC of
170s/24h.
The content of FREQ2 cannot be read and an instruction such as for example
by 0.2% per digit (starting from the default value 128 after RESET). This allows the
cycle to be set to an exactitude of 0.2% which corresponds to an error in the RTC of
170s/24h.
The content of FREQ2 cannot be read and an instruction such as for example
a=FREQ2
leads to uncontrollable erroneous behaviour as the corresponding TOKEN of INTER-
PRETER of the MICRO is not recognised.
PRETER of the MICRO is not recognised.
Note:
YEAR
MONTH
DAY
DOW
are variables which are reserved for the operating system but may not be used for
MICRO.
YEAR
MONTH
DAY
DOW
are variables which are reserved for the operating system but may not be used for
MICRO.
9
• 8 BIT A/D-Wandler
• Digitale Ports I/O
• Beep Ports
• Freq. Eingang
• Serielle. Schnittstelle 9600/19200 Baud
• 2kB BASIC-Programmspeicher
• ladbare Systemerweiterungen (z.B. DCF 77 Synchronisierung der RTC)
• Digitale Ports I/O
• Beep Ports
• Freq. Eingang
• Serielle. Schnittstelle 9600/19200 Baud
• 2kB BASIC-Programmspeicher
• ladbare Systemerweiterungen (z.B. DCF 77 Synchronisierung der RTC)
Für maximale Flexibilität sind Betriebssystemerweiterungen ladbar, die allerdings
den nutzbaren BASIC-Programmspeicher reduzieren. Die Betriebsystemerweiterun-
gen werden von Conrad zur Verfügung gestellt.
den nutzbaren BASIC-Programmspeicher reduzieren. Die Betriebsystemerweiterun-
gen werden von Conrad zur Verfügung gestellt.
Programmer/Evaluation Board
Das P/E Board stellt dem Benutzer eine serielle Schnittstelle mit Pegelwandlung zur
Verfügung um kompilierte Programme aus der Entwicklungsumgebung in die C-
Control Computer der Ausführung MICRO und MICRO zu laden.
Zusätzlich gibt es eine Reihe von Ein/Ausgabemöglichkeiten (LEDs, Beeper, Taster,
Potentiometer) zur Verfügung damit sie die Beispielprogramme oder eigene Anwen-
dungen schnell und bequem ausprobieren können.
Die Stromversorgung erfolgt mit einer 9V Batterie oder einem Steckernetzteil 8 bis
12V
Achtung!
Das P/E-Board unterstützt 19200 Baud aus technischen Gründen nicht (Zeitkon-
stanten im Pegelwandler)
Das P/E Board stellt dem Benutzer eine serielle Schnittstelle mit Pegelwandlung zur
Verfügung um kompilierte Programme aus der Entwicklungsumgebung in die C-
Control Computer der Ausführung MICRO und MICRO zu laden.
Zusätzlich gibt es eine Reihe von Ein/Ausgabemöglichkeiten (LEDs, Beeper, Taster,
Potentiometer) zur Verfügung damit sie die Beispielprogramme oder eigene Anwen-
dungen schnell und bequem ausprobieren können.
Die Stromversorgung erfolgt mit einer 9V Batterie oder einem Steckernetzteil 8 bis
12V
Achtung!
Das P/E-Board unterstützt 19200 Baud aus technischen Gründen nicht (Zeitkon-
stanten im Pegelwandler)