Alto Power (RMS/max.) 101324 데이터 시트

제품 코드
101324
다운로드
페이지 20
 
 
 
BLUETOOTH PAIRING & LINKING 
 
IMPORTANT:  
•  These steps are for wireless audio streaming only. 
•  When pairing or linking, do only one process at a time. Starting one process before the other is finished 
will cancel the first. 
•  The tone sequences for pairing and linking are different, so you can easily distinguish between the two. 
 
ABOUT RANGE 
 
Truesonic wireless loudspeakers use an advanced, extended-range Bluetooth antenna design, allowing for 
ranges far greater than traditional Bluetooth devices. The typical range is 60-80 feet (18-24 meters) with a 
clear line of sight. However, the range may vary depending on your source device and the environment.  
To maximize the range: 
•  Set your source device on a flat surface and make sure there are no obstacles between the 
loudspeaker and your device (e.g., walls, furniture, etc.).  
•  Turn off your source device’s Wi-Fi.  
•  Turn off any unneeded 2.4 GHz devices in the nearby vicinity (e.g., other Bluetooth devices, baby 
monitors, Wi-Fi access points, microwave ovens, etc.). 
•  Try using a different Bluetooth source device. Bluetooth signal strength varies between different 
devices. 
 
PAIRING 
 
To pair the speaker to your Bluetooth device: 
1.
 
Do this on one loudspeaker only: With the loudspeaker powered on, press and release its PAIR 
BUTTON. Its LED will flash, and you will hear a tone sequence from the loudspeaker. (If you are using 
two Truesonic wireless loudspeakers, this one will be the "master." Also see the LINKING section 
below.) 
2.
 
From your Bluetooth device’s settings page, enable 
Bluetooth and select ALTO PRO WIRELESS 
TS115W as the device. When paired successfully, 
you will hear a final "confirmation tone" from the 
loudspeaker and the PAIR BUTTON LED will light 
continuously. (This process may take up to 60 
seconds.) 
Note: If your device prompts you to select the connection type, select “stereo speakers,” “advanced 
audio,” or a similar option. 
3.
 
Turn the loudspeaker's BLUETOOTH VOLUME knob to its lowest setting. 
4.
 
On your Bluetooth device, play music. We recommend setting the playback volume at its maximum 
setting. Then, adjust the loudpeaker’s BLUETOOTH VOLUME knob to the desired level. 
5.
 
Once your device is paired to the speaker, the speaker will remember the device even after power-
cycling it. To reconnect it, go to your device’s Bluetooth settings page and select “Connect” to re-
establish the connection. 
 
LINKING 
 
If you are using two Truesonic wireless speakers:  
1.
 
Make sure no audio is playing from your Bluetooth 
device. If it is, pause/stop playback and wait 5 
seconds. 
2.
 
Press and release the STEREO LINK BUTTON on 
each speaker.   
3.
 
Both loudspeakers’ LEDs will flash while 
"searching" for each other, and you will hear a tone 
sequence from both loudspeakers. (This process may take up to 60 seconds. However, the very first 
time you link the loudspeakers, the process may take up to 3 minutes.) 
4.
 
When they are successfully linked, you will hear a final "confirmation tone" from both loudspeakers and 
the STEREO LINK BUTTON LEDs on both loudspeakers will light continuously.  
 
Note: The stereo signal will be split between the two loudspeakers: the master loudspeaker will play the left 
channel; the slave loudspeaker will play the right channel. 
Tip: When using two loudspeakers, we recommend labeling the master loudspeaker so you can distinguish 
between the two in future setups. 
Bluetooth is a registered trademark of Bluetooth SIG.
Note: If your device prompts you to enter 
a PIN code to pair it to the speaker, enter 
0000 (four zeros).
Note: The loudspeaker that is connected 
to your source device is the “master”; the 
linked loudspeaker is the “slave.” The 
source device sends its signal to the 
master, and the master relays the signal to 
the slave.