Panasonic Door switch 250 Vac 5 A Tappet momentary AZC11013AJ IP40 1 pc(s) AZC11013AJ 데이터 시트
제품 코드
AZC11013AJ
55
METAL PLATE
ATTACHMENT
ATTACHMENT
• Attaching the main unit
1. Using an M4 screw, attach firmly
remembering to employ a washer, etc.
The appropriate torque is 1.18 to 1.47N
(12 to 15kg/cm.)
2. 2. When moveable parts such as the
gate are closed, ensure that the yoke
and metal plate are flush with each
other.
1. Using an M4 screw, attach firmly
remembering to employ a washer, etc.
The appropriate torque is 1.18 to 1.47N
(12 to 15kg/cm.)
2. 2. When moveable parts such as the
gate are closed, ensure that the yoke
and metal plate are flush with each
other.
• Attaching the metal plate
1. Using an M3 dish screw, attach to the side opposite from the yoke. Pay particular
attention that the head of the attached screw does not protrude further than the sur-
face of the metal plate (if using wooden screws, a call of 2.7 is optimum.)
2. If the adhesive side is magnetic (metal plate), the adhesion may prove ineffective.
Further, since the sustainability varies depending on the board thickness and the sur-
face processing (paint, etc.), it is best to check beforehand.
1. Using an M3 dish screw, attach to the side opposite from the yoke. Pay particular
attention that the head of the attached screw does not protrude further than the sur-
face of the metal plate (if using wooden screws, a call of 2.7 is optimum.)
2. If the adhesive side is magnetic (metal plate), the adhesion may prove ineffective.
Further, since the sustainability varies depending on the board thickness and the sur-
face processing (paint, etc.), it is best to check beforehand.
SUITABLE WIRING
• Maximum external dimensions upon
completion
Circular: 8mm dia.
completion
Circular: 8mm dia.
.315 inch dia.
max.
Flat: Lengthwise 9.4mm
.370inch
max.
(VVF 2 cores, conductor radius 1.6 dia.)
• Wiring processing dimensions
Refer to the diagram below for the wiring
processing dimensions
Refer to the diagram below for the wiring
processing dimensions
WIRING
• Terminal uses a M3.5 angle washer
attachment.
• During wiring work, do not connect the
lead wire directly to the terminal, but via
a crimp contact. However, this excludes
single wiring.
• Wiring by solder should be avoided.
1. Wiring method
Insert a flat screwdriver into the indenta-
tion of the product side, and remove the
terminal cover.
attachment.
• During wiring work, do not connect the
lead wire directly to the terminal, but via
a crimp contact. However, this excludes
single wiring.
• Wiring by solder should be avoided.
1. Wiring method
Insert a flat screwdriver into the indenta-
tion of the product side, and remove the
terminal cover.
CAUTIONS FOR USE
• Because the magnelimit is not water-
proof, avoid using in areas where it may
be splashed with either water or oil. Also,
avoid using in locations where dust may
accumulate.
• Do not use in atmospheres where the
unit may directly come into contact with
any kind of organic solvent, strong acid
or alkaline liquids, or combustible or cor-
rosive gasses.
• Avoid using in silicon environments
such as organic silicon-based rubber,
solvents, sealants, oil, grease, or wiring.
• The moveable parts on the magnelimit
such as the gates are equipped with a
stopper, so avoid attachments that
require them to bear the full load.
• In order to improve reliability under
actual working conditions, check the
quality under as close to actual working
conditions as possible.
• This magnelimit has a built-in electro-
magnet. For this reason, take care not to
place floppy disks, magnetic cards, or
other magnetic recording mediums near
the unit, as the data may be corrupted or
lost.
proof, avoid using in areas where it may
be splashed with either water or oil. Also,
avoid using in locations where dust may
accumulate.
• Do not use in atmospheres where the
unit may directly come into contact with
any kind of organic solvent, strong acid
or alkaline liquids, or combustible or cor-
rosive gasses.
• Avoid using in silicon environments
such as organic silicon-based rubber,
solvents, sealants, oil, grease, or wiring.
• The moveable parts on the magnelimit
such as the gates are equipped with a
stopper, so avoid attachments that
require them to bear the full load.
• In order to improve reliability under
actual working conditions, check the
quality under as close to actual working
conditions as possible.
• This magnelimit has a built-in electro-
magnet. For this reason, take care not to
place floppy disks, magnetic cards, or
other magnetic recording mediums near
the unit, as the data may be corrupted or
lost.
Metal plate
Fixed side
Moveable side
Yoke
Magnet plate
screw
C1
Attachment
8 dia. max
.315 dia. max
40
1.575
Flat screwdriver
Indentation
Rubber cap
Terminal cover
9.4
(Lengthwise)
(Lengthwise)
40
8 to 10
.370
1.575
.315 to .394
max
Unit attachment hole processing dimensions
Adhesion board hole processing dimensions
(Fit a C1 panel to the inlet vent)
Unless the metal plate and the yoke are
flush with each other, adhesive power
will be lost, and there is a risk that the
switch will not operate.
flush with each other, adhesive power
will be lost, and there is a risk that the
switch will not operate.
2-4.3
or M4 tap
or M4 tap
52
±0.15
2.047
±.006
.170
dia.
2-3.2
or M3 tap
50
±0.15
1.969
±
.006
.126
dia.
Flat (VVF 2 cores, conductor radius 1.6
.063
dia)
Circular
3. If using a VVF wire, bend the wire
towards the unit, and once it has taken
the proper shape, install the terminal
cover. After installing the terminal cover,
attach the rubber cap.
towards the unit, and once it has taken
the proper shape, install the terminal
cover. After installing the terminal cover,
attach the rubber cap.
2. Slide the rubber cap and the terminal
cover over the wire, as shown in the
illustration then attach a crimp contact to
the terminal. The torque applied to the
terminal screw should be within the
range of 0.39-0.59 Nm (4-6 kg/cm).
cover over the wire, as shown in the
illustration then attach a crimp contact to
the terminal. The torque applied to the
terminal screw should be within the
range of 0.39-0.59 Nm (4-6 kg/cm).
Magnelimit
04/2005