Pizzato Elettrica Foot switch 250 Vac 6 A 1-pedal 1 maker, 1 breaker PA 20301-M2 IP65 1 pc(s) PA 20301-M2 데이터 시트
제품 코드
PA 20301-M2
3
page 3 / 3
General Catalog 2007-2008
Single foot switches PX and PA series
Utilization categories
Alternate current: AC15 (50÷60 Hz)
Ue (V)
Alternate current: AC15 (50÷60 Hz)
Ue (V)
250
400
500
Ie (A)
6
4
1
Direct current: DC13
Ue (V)
Ue (V)
24
125
250
Ie (A)
6
1,1
0,4
Markings:
In conformity with standards:
IEC 60947-5-1, EN 60947-5-1, IEC 529, EN 60529, VDE 0660-200, CENELEC EN 50013.
IEC 60947-5-1, EN 60947-5-1, IEC 529, EN 60529, VDE 0660-200, CENELEC EN 50013.
Electrical data
Thermal current (Ith):
Thermal current (Ith):
10 A
Rated insulation voltage (Ui):
500 VAC 600 VDC
Protection against short circuits:
fuse 10 A 500 V type aM
Pollution degree:
3
Cross section of the conductors (fl exible copper wire)
Contact block combinations
Contact block combinations
:
min.
1 x 0,5 mm
2
(1 x AWG 20)
max.
2 x 2,5 mm
2
(2 x AWG 14)
Conduit entry
with cable-clamp
Knock out opening (to
assemble multiple foot
switches)
Protection degree IP53
or IP65
Non-skid rubber feet
Protection plug
against powder
Contact blocks
For further information see page 2/123
Housing
Made of glass-reinforced polymer, self-extinguishing, shock-proof thermoplastic
resin and with double insulation
Actuating force:
Made of glass-reinforced polymer, self-extinguishing, shock-proof thermoplastic
resin and with double insulation
Actuating force:
16 N
One threaded conduit entry
Protection degree:
Protection degree:
IP53 or IP65
Main data
Polymer housing, three conduit entries
Protection degree IP53 or IP65
Various contact blocks available
Various auxiliary devices available
Assembled through special joining kits
General data
Ambient temperature:
Ambient temperature:
from -25°C to +80°C
Max operating frequency:
3600 operations cycles
1
/hour
Mechanical endurance:
20 million operations cycles
1
(1) One operation cycle means two movements, one to close and one to open contacts, as foreseen by IEC 947-5-
1 standard.
1 standard.
Strong protection polymer made.
Holds more than 80 Kg
Installation for safety applications:
Use only switches marked with the symbol
Use only switches marked with the symbol
. The safety circuit must always be connected with the NC contacts (normally closed contacts:
11-12, 21-22 or 31-32) as stated in the standard EN 60947-5-1, encl. K, par. 2.
In conformity with requirements requested by:
Low Voltage Directive 2006/95/EC, Machinery Directive 2006/42/EC and
Electromagnetic Compatibility 2004/108/EC.
Positive contact opening in conformity with standards:
IEC 60947-5-1, EN 60947-5-1, VDE 0660-206.
Low Voltage Directive 2006/95/EC, Machinery Directive 2006/42/EC and
Electromagnetic Compatibility 2004/108/EC.
Positive contact opening in conformity with standards:
IEC 60947-5-1, EN 60947-5-1, VDE 0660-206.
If not expressly indicated in this chapter, for the right installation and the correct utilization of all articles see requirements indicated
from page 6/1 to page 6/8.