Milan Technology MIL-C1111 전단

 

MIL-C1111

 

•FCC Class A
•UL 1950
•CSA C22.2 No. 950                                                                                                                                                 
•EN60950
•CE 
•– EN55022 Class B
•– EN50082-1

 

This Class A digital apparatus meets all the requirements of the Canadian 
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences 
du Règlement sur le matériel brouilleur du Canada.

 

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) 

•

and the Low Voltage Directive (73/23/EEC) issued by the commission of the European 
Community. Compliance with these directives implies conformity to the following 
European Norms:

•EN55022 (CISPR 22) - Radio Frequency Interference
•EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity
•EN60950 (IEC950) - Product Safety

 

MiLAN Technology warrants to the original consumer or purchaser that each of its 
products, and all components thereof, will be free from defects in material and/or 
workmanship for a period of five years from the original factory date. Any warranty 
hereunder is extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to,
any implied warranty of merchantability or fitness for a particular purpose, except as 
expressly set forth in this warranty. In no event shall MiLAN Technology be liable for
incidental or consequential damages, costs, or expenses arising out of or in connection
with the performance of the product delivered hereunder. MiLAN Technology will in
no case cover damages arising out of the product being used in a negligent fashion or
manner.

 

© 2000 MiLAN, the MiLAN logo, and MiLAN Technology are either trademarks or registered trademarks of 
Digi International, Inc. in the United States and/or other countries. All other trademarks are the property of 
their respective holders.    

 

For prompt response when calling for service information, have the following information ready:
Product serial number and rev; date of purchase; vendor or place of purchase.
You can reach MiLAN Technology technical support at: support@milan.com 
Telephone: +1.408.744.2751    Fax: +1.408.744.2771
MiLAN Technology 1299 Orleans Drive, Sunnyvale, CA 94089-1138 United States of America 
Telephone: +1.408.744.2775    Fax: +1.408.744.2793 
http://www.milan.com      info@milan.com
© Copyright 2000 MiLAN Technology               Printed in the U.S.A.

 

Follow the steps given below to install the MIL-C1111:
1.

Attach a UTP cable from network to MIL-C1111’s RJ-45 port.

2.

Attach a T-type BNC connector from network cabling to the BNC 
connector.

3.

Plug the power adapter into an AC outlet and connect the power 
adapter cord to the unit.

 

: Use shielded UTP (CAT 5) cabling for CISPR 22 classB.  

 

Next to the coax cable connector, there are DIP switches that 
control the 50 Ohm internal resistor. Both switches are shipped in 
the “up” position (default, no termination).

 

1.

If the MIL-C1111 is connected to the end of a multinode segment 
without a T-connector and terminator, enable 50 Ohm resistor by

•

Setting switch 1 “up”

•

Setting switch 2 “down”.

2.

If the MIL-C1111 is connected to a single-nod without a T-type 
connector and terminator on a coax cable of less than one meter’s 
length:

•

Set both switches in the “down” position.

 

: For this configuration, you do not need a 50 Ohm 

terminator on the coax segment of the MIL-C1111’s BNC 
connector.

 

©Copyright 2000 MiLAN Technology   PN 90000213    Printed in the USA

 

   

 

•

 

: Amber, indicates a packet activity on the 10BASE-T net-

work.

•

 

: Amber, indicates a packet activity on the 10BASE2 

network.

•

 

: Green, there is a good link on the 10BASE-T network.

•

 

: Green, coax connection is established.

 

The MDI-X/MDI switch is located on the side of the unit. This 
switch enables a quick configuration of the 10BASE-T port.

 

•

For a hub or repeater, use a swap cable (pins are connected 1 to 3, 
2 to 6, 3 to 1, 6 to 2).

•

For a workstation or PC, use a straight-through cable (pins are 
connected 1 to 1, 2 to 2, 3 to 3, 6 to 6).

 

•

For a hub or repeater, use a straight-through cable (pins are con-
nected 1 to 1, 2 to 2, 3 to 3, 6 to 6.

•

For a workstation or PC, use a swap cable (pins are connected 1 to 
3, 2 to 6, 3 to 1, 6 to 2.

Ethernet

COAX to 10BASE-T

IEEE 802.3 Compliant

COAX ACTIVE

COAX ENABLE

POWER

TX ACTIVE

TX LINK

500 mA

1 2

3 4

5 6

8

7

        MDI
Pin 1=TX+
Pin 2=TX-
Pin 3=RX+
Pin 6=RX-

Pin 1=RX+

Pin 2=RX-

Pin 3=TX+

Pin 6=TX-