White Rodgers F145RF-1600 Wireless Remote Thermostat Sensor 설치 설명서
2
Press Connect
button
LOCATE AND MOUNT REMOTE SENSOR
IMPORTANT
Before drilling holes for mounting the Remote Sensor, verify the area(s) chosen for mounting allows good wireless
communication to the Equipment Control Module. Place the remote(s) where they will be mounted (but do not drill holes yet)
and follow steps in powering remote. If the remote sensors are out of range, status LED on sensor will flash red so a different
location may be required.
communication to the Equipment Control Module. Place the remote(s) where they will be mounted (but do not drill holes yet)
and follow steps in powering remote. If the remote sensors are out of range, status LED on sensor will flash red so a different
location may be required.
POWERING THE REMOTE/CONNECTING TO
1F98EZ-1621
Indoor Remote Sensor
Locate Wireless Remote Sensor(s)
5’ off the ground in an area that
represents the best location to average the temperature between
Comfort Interface and Remote Sensor location.
Remove cover by holding Remote Sensor base and pressing the
tab at the bottom toward the top. Continue to slide cover up to
remove from base.
Use base to mark mounting hole location on wall. Drill mounting
holes. Remote sensor can be attached to wall after checking operation.
For indoor use, the bracket is optional.
Comfort Interface and Remote Sensor location.
Remove cover by holding Remote Sensor base and pressing the
tab at the bottom toward the top. Continue to slide cover up to
remove from base.
Use base to mark mounting hole location on wall. Drill mounting
holes. Remote sensor can be attached to wall after checking operation.
For indoor use, the bracket is optional.
Cover
Base
Mounting
Holes
Slide cover
off of base
2 “AA” batteries
Outdoor Remote Sensor
If the sensor is going to be used outdoors, clip the indoor/outdoor
jumper labelled W
jumper labelled W
1.
Locate wireless remote sensor setup out of direct sunlight. Direct
sun exposure will affect sensed temperature.
Make sure it is mounted in upright position and in a dry location
under a covered area like a bay window or roof overhang.
sun exposure will affect sensed temperature.
Make sure it is mounted in upright position and in a dry location
under a covered area like a bay window or roof overhang.
NOTE
Mounting bracket must be used to mount outdoor sensor to
provide a more moisture resistant seal. Be sure sensor is in up
right position.
A mounting bracket is provided to keep the outdoor sensor away
from the mounting surface and away from water buildup.
Install mounting bracket to wall at desired location. Outdoor
Remote Sensor can be attached to mounting bracket after
checking wireless operation.
from the mounting surface and away from water buildup.
Install mounting bracket to wall at desired location. Outdoor
Remote Sensor can be attached to mounting bracket after
checking wireless operation.
Clip W
1 for
outdoor use
Bracket
mounting
holes
Mounting
holes
Up
1. Install batteries to power remote. LED will flash red and go off.
2. Go to Equipment Control and press the Connect button.
Equipment Control Status LED will blink green indicating
searching for wireless devices.
searching for wireless devices.
3. Press and hold the Connect button located on the inside of
the Remote Sensor about until LED starts flashing green then
release button. At the end of the flash sequence, observe
release button. At the end of the flash sequence, observe
three
rapid flashes of the LED to indicate that pairing has occurred.
4. The LED will switch to flash amber indicating the sensor
number assigned.
1 amber flash = sensor 1
2 amber flashes = sensor 2
3 amber flashes = sensor 3
4 amber flashes = outdoor sensor 4
5. Remove one battery from the Remote Sensor. Wait for about 10
seconds and reinstall the battery.
DH
M
2
DH
M
HM
2
HM
L
SYST
EM
POWE
R
RC
R
C
LED On/Off
Connect
W/E
W2
Y
Y2
G
O/B
L
HM
HM2
DHM
SY
S
DRY
SY
S
DHM2
RC
RH
R
C
DRY
Equipment Control Module
Remote Sensor
DH
M
2
DH
M
HM
2
HM
L
SYST
EM
POWE
R
RC
R
C
LED On/Off
Connect
W/E
W2
Y
Y2
G
O/B
L
HM
HM2
DHM
SY
S
DRY
SY
S
DHM2
RC
RH
R
C
DRY
Press Connect
button