Sony NAS-SV20DI 사용자 설명서
31
GB
Ne
twor
twor
k co
nne
ction
s
5
Select “Wired LAN.”
The unit automatically starts setting up the
network connection.
network connection.
6
When “Save settings and check
connection. Press ENTER to
continue.” appears, press ENTER.
connection. Press ENTER to
continue.” appears, press ENTER.
It may take a while for the unit to complete
the network settings.
When the network settings have been
completed, “Complete.” appears.
If you are making the initial settings, the
“Date&Time” display, step 5 of “Performing
initial setup operations,” appears. Go back to
page 22 and continue the initial setting
process.
the network settings.
When the network settings have been
completed, “Complete.” appears.
If you are making the initial settings, the
“Date&Time” display, step 5 of “Performing
initial setup operations,” appears. Go back to
page 22 and continue the initial setting
process.
7
Make the server settings.
To listen to audio content stored on the server
through the network that you have set up in
this section, you need to set up your server
(page 38).
through the network that you have set up in
this section, you need to set up your server
(page 38).
Setting up the IP address/
proxy server
proxy server
You may have to use a fixed IP address and proxy
server, depending on your home network settings,
or the specifications of the Internet service
provider.
For details on the input values in the following
procedures, refer to the operating manual of the
respective device or the information provided by
your Internet service provider.
server, depending on your home network settings,
or the specifications of the Internet service
provider.
For details on the input values in the following
procedures, refer to the operating manual of the
respective device or the information provided by
your Internet service provider.
To use a fixed IP address
The unit is set to obtain the IP address
automatically as the factory setting, however, you
can use a fixed IP address, depending on your
network settings.
automatically as the factory setting, however, you
can use a fixed IP address, depending on your
network settings.
1
Press SETTINGS to enter the
settings menu and select “Network
Settings.”
settings menu and select “Network
Settings.”
2
When “Playback and network
functions cannot be used during the
setup. Press ENTER to continue.”
appears, press ENTER.
functions cannot be used during the
setup. Press ENTER to continue.”
appears, press ENTER.
When “
” is displayed, the message is
continued to the next page. Press
m to see the
entire text string.
3
Select “Tools” - “Advanced Settings.”
4
Select “IP Address Settings” -
“Manual.”
“Manual.”
5
Enter the values for “IP Address,”
“Subnet Mask” and “Default
Gateway.”
“Subnet Mask” and “Default
Gateway.”
When you press ENTER after you enter
“Default Gateway,” the DNS server settings
display appears.
For details on how to input characters, see
“Entering text” (page 19).
“Default Gateway,” the DNS server settings
display appears.
For details on how to input characters, see
“Entering text” (page 19).
6
Enter the values for the “Primary
DNS” setting.
DNS” setting.
7
When “Set Second. DNS?” appears,
select “Yes.”
select “Yes.”
If you do not have to set the secondary DNS
server setting, select “No.”
server setting, select “No.”
8
Enter the values for the “Secondary
DNS” setting, and then press
ENTER.
DNS” setting, and then press
ENTER.
9
When “Save settings and check
connection. Press ENTER to
continue.” appears, press ENTER.
connection. Press ENTER to
continue.” appears, press ENTER.
When the network settings have been
completed, “Complete.” appears.
completed, “Complete.” appears.
Tip
If you want to obtain the IP address automatically using
DHCP, select “Auto” for the “IP Address Settings” in step
4. If you select “Auto” in step 4, the “DNS Settings”
selection display appears afterwards. In this case, select
“Auto” or “Manual” for “DNS Settings” and enter the
respective values following the instructions that appear on
the display.
DHCP, select “Auto” for the “IP Address Settings” in step
4. If you select “Auto” in step 4, the “DNS Settings”
selection display appears afterwards. In this case, select
“Auto” or “Manual” for “DNS Settings” and enter the
respective values following the instructions that appear on
the display.