United States Stove VFZC32L 사용자 설명서
MANTEL INSTALLATION
This fireplace may be installed using the cabinet mantel with hearth base accessory against
a wall in your home. You must use one of the Satin Black or Polished BrassTrim Kits
available when installing your fireplace with the optional mantel kit. (See Accessories on
page 28 & 29). NOTE: The Trim Kits provide a finished appearance covering rough and/or
unfinished mantel edges.
a wall in your home. You must use one of the Satin Black or Polished BrassTrim Kits
available when installing your fireplace with the optional mantel kit. (See Accessories on
page 28 & 29). NOTE: The Trim Kits provide a finished appearance covering rough and/or
unfinished mantel edges.
NOTE: The instructions below show installation using the VFGO32M/VFUF32M series
cabinet mantels and the VFGO32B/VFUF32B series hearth base accessories. The hearth
base accessory shown is optional for this installation. You can install the fireplace and mantel
directly on the floor. The VFUN32FM face mantel accessories cannot be installed with the
VFGO32B/VFUN32B series hearth base. You must install the face mantels directly on the
floor.
NOTE: If using the VFUF32FM series face mantel accessory, a wall recess opening will be
needed. See installation instructions for VFUF32FM series face mantel accessory.
cabinet mantels and the VFGO32B/VFUF32B series hearth base accessories. The hearth
base accessory shown is optional for this installation. You can install the fireplace and mantel
directly on the floor. The VFUN32FM face mantel accessories cannot be installed with the
VFGO32B/VFUN32B series hearth base. You must install the face mantels directly on the
floor.
NOTE: If using the VFUF32FM series face mantel accessory, a wall recess opening will be
needed. See installation instructions for VFUF32FM series face mantel accessory.
1.
Assemble cabinet mantel, hearth base (optional), and trim accessories.
Assembly instructions are included with each accessory.
Assembly instructions are included with each accessory.
2.
If using an optional VF32B blower, install a properly grounded, 120 volt three-prong
electrical outlet at firebox location if an outlet is not there. If possible, locate outlet so
cabinet mantel will cover it when installed (see Figure 11, below).
electrical outlet at firebox location if an outlet is not there. If possible, locate outlet so
cabinet mantel will cover it when installed (see Figure 11, below).
3.
Install gas piping to fireplace location. For this installation you will need an approved
flexible gas line (if allowed by local codes) and a manual shutoff valve. The flexible gas
line must be the last item installed on the gas piping. See Connecting to Gas Supply
on pages 14 & 15.
flexible gas line (if allowed by local codes) and a manual shutoff valve. The flexible gas
line must be the last item installed on the gas piping. See Connecting to Gas Supply
on pages 14 & 15.
4.
Place (optional) hearth base accessory against wall at installation location. Cut an
access hole in hearth top to run flexible gas line to fireplace (see Figure 11). Make sure
to locate access hole so cabinet mantel will cover it when installed. Note: you can secure
base to floor using wood screws. Countersink screw heads and putty over.
access hole in hearth top to run flexible gas line to fireplace (see Figure 11). Make sure
to locate access hole so cabinet mantel will cover it when installed. Note: you can secure
base to floor using wood screws. Countersink screw heads and putty over.
Fireplace Installation Using Optional Mantel.
Figure 11 - Placing (optional) Hearth Base against wall
Hearth Base
Flexible Gas Line
Electrical Outlet
Gas Line
Access Hole
Access Hole
16
NOTICE
A qualified service person must connect fireplace to gas supply. Follow all local
codes.
codes.