Studer Innotec AJ SERIES 사용자 설명서
STUDER INNOTEC
AJ
AJ V2.1
3/24
English description
Introduction
The sine wave inverters of the AJ series
have been designed to meet industrial
and domestic needs. They meet the
highest requirements of comfort, safety
and reliability.
Any device designed for the public
electrical network of 230 V 50 Hz can be
connected to them (up to the nominal
power of the inverter).
The AJ series is the perfect source of
voltage in any place where the public
network is not available.
This document is an essential part of the
inverter and must always be carried with
it and be at the disposition of anyone
working on the installation.
Should you have any doubt or question,
do not hesitate to contact your specialist
salesperson who will give you the best
advice.
have been designed to meet industrial
and domestic needs. They meet the
highest requirements of comfort, safety
and reliability.
Any device designed for the public
electrical network of 230 V 50 Hz can be
connected to them (up to the nominal
power of the inverter).
The AJ series is the perfect source of
voltage in any place where the public
network is not available.
This document is an essential part of the
inverter and must always be carried with
it and be at the disposition of anyone
working on the installation.
Should you have any doubt or question,
do not hesitate to contact your specialist
salesperson who will give you the best
advice.
Warning
A deficient assembly could result in
damage to the device, cause function
failures or potential damage to the
users.
The working device generates a high
voltage which might be lethal in case of
contact. So, any manipulation of the
inverter must be carried out with utmost
care.
damage to the device, cause function
failures or potential damage to the
users.
The working device generates a high
voltage which might be lethal in case of
contact. So, any manipulation of the
inverter must be carried out with utmost
care.
THE OWNER MUST NOT
MANIPULATE ANY PIECE INSIDE
THE INVERTER.
Opening the inverter or using it
incorrectly will result in the immediate
loss of the warranty.
No current or tension generating device
(public grid, generator,... ) may be
connected to the outlet of the inverter
MANIPULATE ANY PIECE INSIDE
THE INVERTER.
Opening the inverter or using it
incorrectly will result in the immediate
loss of the warranty.
No current or tension generating device
(public grid, generator,... ) may be
connected to the outlet of the inverter
because this could result in its
destruction.
destruction.
The inverter AJ is to be used only with a
lead battery. As for the use of batteries,
follow the manufacturer’s instructions.
lead battery. As for the use of batteries,
follow the manufacturer’s instructions.
Installation
The AJ sine wave inverter is an
electronic device, for which some
caution must be taken when installing it:
Place where the inverter is to be
installed:
Out of reach of unauthorised persons,
specially children.
In a dry place (max. 95% humidity), and
in any case with no condensation.
Not directly on top of the batteries.
Ventilation must be free, and a space of
10 cm. on each side is needed for good
evacuation of the internal heat.
electronic device, for which some
caution must be taken when installing it:
Place where the inverter is to be
installed:
Out of reach of unauthorised persons,
specially children.
In a dry place (max. 95% humidity), and
in any case with no condensation.
Not directly on top of the batteries.
Ventilation must be free, and a space of
10 cm. on each side is needed for good
evacuation of the internal heat.
Fitting the inverter
The inverter is fitted by screws (max.
4mm for AJ 275-AJ 1300 or max. 8mm
for AJ 2100 and 2400) using the four
holes provided. The fitting screws are
not supplied with the inverter. It may be
fit into any position.
The inverter is fitted by screws (max.
4mm for AJ 275-AJ 1300 or max. 8mm
for AJ 2100 and 2400) using the four
holes provided. The fitting screws are
not supplied with the inverter. It may be
fit into any position.