Sigma C4 사용자 설명서

다운로드
페이지 120
3
C4 Manual Rev 7.5.2
TABLE  OF  CONTENTS
1.  INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Models C4 & CC-3
.5
  Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2  General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3  Custom Features / Interchangeability WARNING . . . . . . . . . . . . . . . . . . 11
1.4    Release  7.5.2  Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.5    C4    vs.  CC-3  Differences  (What’s  New) . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.1  Hardware & Stability Improvements . . . . . . . . . . . . . . . . . . . . . 12
1.5.2  Hardware Change (EEPROM replaces BBSRAM) . . . . . . . . . . 12
1.5.3  Firmware Uploads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5.4    Forced  Start  from  PROM  Firmware . . . . . . . . . . . . . . . . . . . . . 13
1.5.5  Front Panel Information Display at Startup . . . . . . . . . . . . . . . . 13
1.5.6  Temperature Out of Range Shutdown . . . . . . . . . . . . . . . . . . . 13
1.5.7  Internal Error Shutdown Conditions . . . . . . . . . . . . . . . . . . . . . 14
1.5.8  Fahrenheit Temperature Scale Supported . . . . . . . . . . . . . . . . 14
1.5.9  Temperature Probe Correction (Calibration) . . . . . . . . . . . . . . . 14
1.5.10    “Bumpless”  Temperature  Control . . . . . . . . . . . . . . . . . . . . . . 14
1.5.11  Intelligent 2 Probe Control  (Probe Averaging) . . . . . . . . . . . . 15
1.5.12    Default  Setup  Parameters  Restore . . . . . . . . . . . . . . . . . . . . . 16
1.5.13  Program Mode Step Insert & Delete . . . . . . . . . . . . . . . . . . . . 16
1.5.14  Program Mode Any Step Points to Step 100 . . . . . . . . . . . . . 16
1.5.15  Program Mode Safer Program Clear . . . . . . . . . . . . . . . . . . . 16
1.5.16  Program Mode Run Time Program Pre-check . . . . . . . . . . . . 16
1.5.17  Remote Mode EIA-232 Baud Rate Improvement . . . . . . . . . . 16
1.5.18  Remote Mode EIA-232 Port Initialization . . . . . . . . . . . . . . . . 17
1.5.19  Remote Mode Fault Tolerant Parser . . . . . . . . . . . . . . 17
1.5.20  Remote Mode System Information Queries . . . . . . . . . . . . . . 17
1.5.21  Remote Mode Operation Information Queries . . . . . . . . . . . . 17
1.5.22  Remote Mode Setup Parameter Commands . . . . . . . . . . . . . 18
1.5.23  Remote Mode IEEE-488 (GPIB) Monitoring . . . . . . . . . . . . . . 18
1.5.24  Setup Mode Easier Parameter Access . . . . . . . . . . . . . . . . . . 18
2.    PHYSICAL  DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1  Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1.1    Digital  LED  Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1.2    LED  Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1.3  Mode Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.1.4  Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2  Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.    GENERAL  OPERATION  &  ERROR  CONDITIONS . . . . . . . . . . . . . . . . . . . . . . 23
3.1  Startup  Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.1  Model Number and Firmware Version Number Display . . . . . . 23
3.1.2  Temperature Range Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.3  Serial  Number  Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24