Russound CA4 Controller Kit CA4 사용자 설명서

To control universal TV, VCR or DVD, cable or satellite receivers, amplifier or tuner, and 

auxiliary  devices  with  the  CA4-RC  you  need  to  program  the  remote. You  will  need  to 

install the batteries and have enough room to point the CA4-RC at the various source 

equipment. Before proceeding, find the codes for the devices you want to program in 

the “Manufacturer’s Codes”, and write them down or highlight them. Note: Record which 

device is identified as Source 1, 2, 3, and 4. 

Turn on the device and, if needed, load media.

1. 

Press the source key identified with that device. 

2. 

Press and hold SET until the red LED blinks twice, then release.

3. 

Enter the first five-digit code for your device. The LED blinks once as each digit is 

4. 

entered. If the code is correct, the LED blinks twice.   Note:  If the LED does not blink 

twice, repeat steps 2 to 4 and try entering the code again.
Aim the remote at the device and press Power. The device should turn off. If it does 

5. 

not,  repeat  steps  3  to  5,  trying  each  code  for  your  brand  until  you  find  one  that 

works. If you cannot find a code that works, see Searching for Your Code.
Repeat  steps  1  to  5  for  the  other  devices  you  want  to  control. Write  down  each 

6. 

working device code.

Set - Press and Hold until 

LED flashes appropriately 

Power - Controls Source 

On/Off

LED - flashes indicating programming and talkback

Source - Selects source 

to be controlled 

Numeric Keypad - Enter IR 

codes and numeric input 

If you have set up the remote using the procedure in “Searching for Your Code,” you 

may need to find out which five-digit code is operating your equipment. For example, to 

find out which code is assigned to your TV:

Press the source key to which the TV is assigned.

1. 

Press and hold SET until the red LED blinks twice, then release.

2. 

Enter 9-9-0. The LED blinks twice.

3. 

To view the code’s first digit, press 1. Count the LED blinks (e.g., three blinks =3), 

4. 

and enter the number in the appropriate device listed in step 3 of "Programming a 

Device." If a code digit is 0, the LED does not blink.
Repeat step 4 for the remaining digits, using 2 for the second digit, and so on.

5. 

To check for other device codes, repeat steps 1 to 5, using the appropriate key.

6. 

If the device does not respond to the remote after trying all codes listed for your brand, 

or if the brand is not listed, try searching for the code:

Press a source key once.

1. 

Press and hold SET until the red LED blinks twice, then release.

2. 

Enter 9-9-1, then the device group number (see below). The LED blinks twice.

3. 

 

 

0  Cable (Cable Converters, Video Accessories, Satellite Receivers) 

 

 

1   TV (TVs) 

 

 

 

 

 

 

 

2   VCR (VCRs, DVD players)  

 

 

 

 

 

3   Audio (Audio Amplifiers, Audio Amp/Tuners, CD Players)
Aim the remote at the device and press POWER. The remote sends IR codes from its 

4. 

library to the selected device, starting with the most popular code first. If the device 

responds, go to step 6.
If  the  device  does  not  respond,  press  CH+.  the  remote  will  try  the  next  code. 

5. 

Continue until the device responds. Press CH- to try the previous code.
Press SET to lock in code. To search for other device codes, 

6. 

repeat steps 1-5.