Rangemaster 90 CERAMIC U109650-02 사용자 설명서
30
SERVICING - WARNING
Disconnect from the electricity before servicing. Check appliance is safe when you have finished.
12. To Change Main Oven Door Catch
Remove outer door panel (see 15). Remove screws ‘B’
holding catch assembly to inner door panel. Fit new catch
and reassemble in reverse order.
Check correct door operation.
holding catch assembly to inner door panel. Fit new catch
and reassemble in reverse order.
Check correct door operation.
13. To Adjust Main Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep, and
screw in or out as required until required fit is obtained.
screw in or out as required until required fit is obtained.
Retighten locking nut.
14. To Change Oven Door Seal
Open oven door. The seal is held in place by small hooks on
the rear face. At the corner pull seal diagonally away from
the door centre until that hook is released. Proceed to the
next hook and release it in a similar way, and so on.
the rear face. At the corner pull seal diagonally away from
the door centre until that hook is released. Proceed to the
next hook and release it in a similar way, and so on.
When fitting new seal, position the seal join at the bottom.
Hook the new seal in one of the corner holes of the door,
and proceed round the door snapping in each hook in turn.
Hook the new seal in one of the corner holes of the door,
and proceed round the door snapping in each hook in turn.
15. To Remove Oven Inner Back.
Open the oven door. Remove oven furniture. For the Left
hand oven unscrew the 2 thermostat phial fixing screws.
hand oven unscrew the 2 thermostat phial fixing screws.
Remove the fixings that secure the inner back to the oven rear.
Lift the removable panel away. Re-assemble in reverse
order. Ensure that the retaining fixings are fully tightened.
For the Left hand oven unscrew the 2 thermostat phial
fixing screws. Remove the screws that secure the inner
back to the oven rear. Lift the removable panel away. Re-
assemble in reverse order. Ensure that the retaining fixings
are fully tightened.
order. Ensure that the retaining fixings are fully tightened.
For the Left hand oven unscrew the 2 thermostat phial
fixing screws. Remove the screws that secure the inner
back to the oven rear. Lift the removable panel away. Re-
assemble in reverse order. Ensure that the retaining fixings
are fully tightened.
16. To Replace an Oven Fan
Disconnect from electricity supply.
Pull the unit forward to access the cover boxes at the rear of
the appliance. Remove the fixings that secure the cover and
lift it clear. Remove the fan wiring, noting the connection
positions. Remove the inner back as detailed in Section 20.
Hold the fan blades and undo the centre nut (Left hand
thread), brass washers, fan blade and Circlip. Undo the
fixings that retain the fan and remove it from the cavity rear.
Fit the replacement and re-assemble parts in reverse order.
Check that the oven operates satisfactorily.
Pull the unit forward to access the cover boxes at the rear of
the appliance. Remove the fixings that secure the cover and
lift it clear. Remove the fan wiring, noting the connection
positions. Remove the inner back as detailed in Section 20.
Hold the fan blades and undo the centre nut (Left hand
thread), brass washers, fan blade and Circlip. Undo the
fixings that retain the fan and remove it from the cavity rear.
Fit the replacement and re-assemble parts in reverse order.
Check that the oven operates satisfactorily.
17. To Remove an Oven fan Element
Disconnect from electricity supply.
Remove the inner back as detailed in Section 20. Remove
the fixings that secure the element within the oven and
lift the element away carefully. Disconnect the leads and
connect to the replacement element and re-assemble parts
in reverse order. Check that the oven operates correctly.
Remove the inner back as detailed in Section 20. Remove
the fixings that secure the element within the oven and
lift the element away carefully. Disconnect the leads and
connect to the replacement element and re-assemble parts
in reverse order. Check that the oven operates correctly.
18. To Remove Grill Element.
Disconnect from electricity supply.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from grill
roof, 2 screws and washers. Remove 2 screws and washers
securing the grill element front support. Remove 1 screw
from each of the grill elements and withdraw grill elements
from grill chamber. Disconnect the leads and connect to
the replacement elements and re-assemble parts in reverse
order. Check operation of grill.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from grill
roof, 2 screws and washers. Remove 2 screws and washers
securing the grill element front support. Remove 1 screw
from each of the grill elements and withdraw grill elements
from grill chamber. Disconnect the leads and connect to
the replacement elements and re-assemble parts in reverse
order. Check operation of grill.